41771722510 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Francis from Middletown, NY
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Tumbler not moving
Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from SHERIDAN, CA
- Parts Used:
- 137513300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Glide was broken
I watched the video on the repair and followed it. Super easy. Repair only took 30 mins. Please note there are 2 glides. Make sure to order 2.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from COLUMBUS, WI
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint screen had holes
took out the old one and put in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from tahlequah, OK
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bearing went out
took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Batesburg, SC
- Parts Used:
- 5303207102
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
strike broken
popped in one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omar from Rumford, ME
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Damaged Filter
Took out the damaged lint filter and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from DUNN, NC
- Parts Used:
- 5304516871
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer lint filter was all torn up after 12 years of use.
Simple: I ordered the part from you then took out the old old and inserted the new one. Took all of 1 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PORT CLINTON, OH
- Parts Used:
- 5303281153
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Squeaking
Watched Video Provided. Very Simple Repair. Asked my lovely wife to hold drum in place while replacing drive belt. She gladly complied and is back doing what she seems to love most. And no, I'm not kidding. Our washer and dryer seem to run 24/7/365. I've completed various repairs on both appliances over the last couple of years and saved 100's of dollars thanks to this site .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from BROOKLYN, NY
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Just popped the part I ordered right in and it's was closing in no time !
Just opened package and popped the part right in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CUMMING, GA
- Parts Used:
- 134222900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top hinge on clothes dryer separated, leaving door difficult to open/close
Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from madison, OH
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The clothes were not getting dry, no matter how long they ran
The first thing I did was logged onto the internet to search the web for my dryer information. Next, after I found the correct model, the site referred me to the parts section and that is where I determined the problem was the M series ignition coil. I then unplugged the dryer and turned off the gas. I took a screwdriver and popped the top off and cut the wire straps that held the door strips and the light to the front panel. I then unplugged the door switch at the connector - HOWEVER - DO NOT TRY TO REMOVE THE WIRES FROM THE ACTUAL DOOR SWITCH BECAUSE THEY ARE VERY FRAGILE AND CAN EASILY BREAK. Next, I removed the two screws that hold the front panel on. By using a slight bit of pressure, I removed the front panel and was able to locate where the ignition coil switch was. (It was right in front) I then removed the two screws that held the clamp down, as well as the bad coils. The coils easily slid off the post and the new pieces slid back on just as easy. I then replaced the screws and clamps to hold the new pieces in place and replaced the front panel. **NOTE ~ while the front panel is off, it would be a good time to clean out all the built up dirt and lint that has accumulated over the years. Lastly, I re-connected all switches and wires and replaced the top panel. Once I turned the gas back on, everything ran beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan D from REDLANDS, CA
- Parts Used:
- 137551901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
the attached anchors and holes linled up about 80% of the time.
I cut off the four that didn't line up - I suppose since this was a gasket that fit several makes, I should expect this type of problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Olmsted, IL
- Parts Used:
- 134587700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer not heating
Very slowly and carefully, you tube videos and schematic very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from HGHLNDS RANCH, CO
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
load squeal
replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from UXBRIDGE, MA
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken belt
Watched video sent to me after I purchased belt on line. Super helpful!
Was this instruction helpful to you?
Thank you for voting!