1107109710 Kenmore Washer Dryer Combo - Instructions

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

Unplugged the power while the washer was running, and the water kept on running. The water inlet valve was stuck open. I removed the inlet valve and you cold blow air thru it, it should be closed with no power applied.Ordered replacement from this site it was a perfect fit. As far as the removal and installation procedure, just follow the video as presented on this site. Good Look.

Turn off water, unplug machine
Disconnect water lines to the valve
Unscrewed the clear plastic tabs on the top of the machine, then pryed the back away from the top white part.
Two gold clips can be popped out with a long flat head screw driver.
Pulled the back away from the machine enough to disconnect the wires from the valve. Unscrew the screw(s) from the valves.
Old valves out, new valves in. Plug in the wires, screw in the screws.
Then, to get the gold tabs back in place.....i called NASA.
just kidding. They're tough!
I slipped one into the back and held it in place with my thumb. Then I lined the piece up with the slot inside the machine. Then, i pryed the top white part away as I pushed them together. Stuck a long handle screwdriver down in and pushed REALLY hard on the gold tab to get it to snap into place. Everything is really tight, so you might have to try it a few times.....i left some blood behind.
repeat for the other side, snap in the clear tabs, hook up the water lines, plugged it in......
Then I sat back and listened to my wife praise me for fixing her machine!

I had to call in to find the correct part because the online recommended part looked very different, and the one found using the model number had no photo, so I was VERY leary of ordering. The service rep said that Kenmore products did not always show up correctly and he gave me the part number needed and there was a photo. The part was not exactly the same, but looked very similar and it was more than 50% less than the original recommended part and part with no photo. I thought that the problem finding Kenmore parts was odd since Kenmore is like number one, right? Part took 3 days to arrive, which I thought was great. Turned off power and water. Removed water hoses. Removed three screws from the back of the top (front loader). Removed the top. Removed a screw holding on the water inlet valve from the outside of the unit through the back cover which required a star driver. Unattached the 4 electrical leads. Unattached the outlet water hose (held on with a squeeze type metal clamp -not sure of the exact name for these). The problem that I had was that the water outlet hose bib attachment was slightly larger than the old one, so the hose would go back on, but the clamp was too small so I cusses a lot before figuring out the problem. I had to go and purchase a new larger clamp. After that, I simply attached the electrical connections and put the outlet back on. One other small problem was that the place where the screw through the back cover was originally attached no longer lined up with the new valve. The plastic piece was shorter than the old one so the screw hole did not line up with the hole in the back panel. The screw isn't really necessary. Overall, replacing the part was easy and I was pleased with the process.

Removed two clips on back panel holding control panel.Removed end plates on control panel. removed two front screws holding control panel. removed wiring harnesses noting location. Set control panel aside. Removed two large clips holding rear panel to washer cabinet. Pulled washer cabinet from the front away from the rear panel and tube. Removed two screws holding water inlet valve. Removed water inlet hose from inlet valve using channel lock pliers. Installed new water inlet valve using supplied mounting bracket. Reassembled washer in reverse order.

I just followed the instructions found on this website. It covered everything you need to know. I have just one thing to add though. Look over everything first and formulate a game plan. Keep all screws etc. and put them in a plastic bag so you don't lose them. You might try using a heavy hammer to force the clips holding the back panel to the top of the machine back in place. One more thing; use a piece of wood to set the back panel on while you replace the intake valve.

Pop out the old latch and replaced with a new one

took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......

the part fit perfectly, it just snaped right into place.

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

just put the new part in the door---sooo easy! THANK YOU!

I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.