1107109901 Kenmore Washer Dryer Combo - Instructions

removed the broken part and replaced with the new one

Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!

First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in about 10 minutes.

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

This was a classic easy repair and I am sure saved us bundles on a service call.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

take the old latch out and pop the new one in. Your repair kit worked perfect.

Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you

Fantastic site and service !!! Using your site, I i'd my needed part in about 10 minutes. I received my Whirlpool dryer door latch part from you in less than 12 hours. Per your internet site instructions, I replaced the part in a few seconds (just popped it into the slot) and my wife had a working dryer for her Sunday wash. I would have been out $55 and 4 to 7 days waiting for a service call if I had used my home warranty service contractor. Using your service, the part(s) and shipping were just over $12.

ordered new latch kit and repaired, very easy thank you

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

Took 5 seconds, just snapped in the slot, didn't need any tools.

Snapped latch into existing hole in 2 seconds. The pin that goes into latch was still intact. That's it ,real simple. The only problem I will hopefully not have in the future is the the mico-switch which is just hanging in there, the switch works but the lever that extends out from the face, that works with the door is partially broken off and the switch is no longer available on your parts list. The appliance is twenty-one years old. I am very happy with your service and I received the parts the next day, after I ordered them and I will be buying more parts in the months to come. This time it will be for my Kenmore gas stove and then a Kenmore refrigerator door hinge.