41799170800 Kenmore Washer Dryer Combo - Instructions

I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.

first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.

Replace the Drum Bearing and Shaft

i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in

First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.

removed the drum out the front and replaced

Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

There are really good instructions with photos on line - search squeeky dryer. I would add that it is easier if you mount the new bearing assembly on the drum before placing the drum back in the dryer cabinet. I guess this is obvious but was not stated in the referenced instructions. The round bearing slotts fairly easily into the plastic pillow block mounted on the back of the cabinet. Just make sure the small ball bearing remains in the center groove - lots of greese will help this.

Lift washer lid by jerking the lid up and open. Remove front panel by removing 2 screws at front bottom and guiding tabs out of slots. Locate tabs on tub cover and gently pry loose with a flat blade screwdriver or putty knife. Remove tub cover and inspect seal area for damage or debris. Replace new tub cover on tub and align and fasten each tab. Ensure that lid is securely fastened to tub by pressing top of cover down and visually inspecting that each tab is engaged with tub hooks. Replace front panel. Use anti-seize grease when replacing the 2 front panel screws. Use a small amount of petroleum jelly on the top lid spring clips before closing washer top. (The last 2 tips will help any future opening of the washer.)

Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pulled hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.

Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.

This was for my Daughter's dryer. A helper really makes this quick and easy. First of all-UNPLUG the unit from the wall. I pried the top up with flat screwdriver. Laid the top back against wall. Removed the two wires from the door cut-off switch. Then removed the two screw attaching the front to the cabinet. Removed the small access panel on back of cabinet. Depressed the belt tensioner to release pressure on the leather drive belt. Went back to front, pushed the belt to the rear of cabinet, then lifted the back of drum to pop the bearing up and out of the plastic cup. I then tilted the drum forward and down and removed through front of cabinet. Reached inside the drum with Phillips screwdriver, removing the two screws to realease the bearing and BB bracket from back of drum. I attached the new bearing cup with BB to the back of cabinet, filling the cup with the high temp grease provided in the cup. Before installing the new bearing on the drum, I ran the new screws into and back out of the new bearing to cut the threads, making it easier to attach on the drum. I then put the drum back into the cabinet popping the bearing into the top of the plastic cup. Next I went to the back, put a bit of grease on the shaft that the tensioner bearing rides on. I re-set the belt on the tensioner, making sure the belt was back in the original position around the drum. I then re-attached the front cabinet centering the front of the drum on the felt. This felt supports the front of the drum. I manually gave the drum a few turns to make sure the drum was centered properly, and belt was mounted correctly. I then re-attached the two wires to the door switch. Slid the dryer into position, inserted the plug back into the outlet. Turmed it on, and now the dryer runs like new again. My Daughter is happy again. You will want to have a vac handy because it is unbelievable how much lint and dust are in the cabinet. I also took the filter bracket apart and cleaned it too.