11089675700 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from BATON ROUGE, LA
- Parts Used:
- 285805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
leaking valves
We watched a video on YouTube; it was very easy . We had to use the mounting bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryanne from BEND, OR
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Drain hose leaking
Followed instructions other customers provided for hose installation. Haven't installed agitator dogs yet. Need to watch the video on your web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from GREENSBURG, PA
- Parts Used:
- 285805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Squealing noise when filling washer; water leak in tub; cold water filling slowly.
Removed screws from top control panel. Tilted panel back. Unsnapped two retaining clips and pulled entire washer cover forward. Turned off water and uplugged washer. Disconnected hot and cold water supply. Disconnected supply tube from water inlet valve. Disconnected electrical hook-ups to water inlet valve. Removed water inletvalve. Installed new valve being careful to use new mounting plate supplied and making sure screw holes line up correctly. Re-connected all disconnects and it works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Danbury, WI
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Top agitator did not work
I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from MORGAN, VT
- Parts Used:
- 279173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out switch
My wife did the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from york, PA
- Parts Used:
- W10820036
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer would not run
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILLIP from AUSTIN, MN
- Parts Used:
- 279827
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Start and then kick out.
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from st louis, MO
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
dryer wasnt heating up, though it would run
Removed the dryer's back panel and took a look. Had no idea what to do next, so I read up on it. Partselect was extremely helpful to me, the exploded views with the part numbers called out were particularly helpful. So I determined it was the thermal fuse. Unscrewed the screw holding in the fuse and disconnected the electrical supply. New fuse went in really easily. Job took a lot longer than it had to cause since I was in there, I cleaned out the dryer really good.
Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!
Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorise from Donalsonville, GA
- Parts Used:
- 3394652
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable)
a broken belt
my hany man did it....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from RCH CUCAMONGA, CA
- Parts Used:
- WP3392519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
My dryer would not heat. Drum was spinning fine and everything else was working just no heat.
I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from N. Ferrisburg, VT
- Parts Used:
- W11613302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket was falling off, needed replacement
Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from TUSCARORA, NV
- Parts Used:
- W10828351
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Lint filter on dryer had broken apart
Replacement fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kansas City, MO
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The water was not switching properly, hot water was barely coming out.
Installed part, now it works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MONA from SHAMROCK, TX
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would not start.
I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.
Was this instruction helpful to you?
Thank you for voting!