41799463820 Kenmore Washer Dryer Combo - Instructions

removed the two 'lock down flanges' from the back of the machine, lifted the top from the front and slid it forward to access the valve. Removed the two electrical connections then the compression ring from the hose on the output side. Removed two screws holding the valve in place, then reversed the process.

I wish this valve was made of metal rather than plastic. I had to replace it because the threads were stripped. Here's the heads up. Make sure the fittings on your supply hoses are 'clean' or you'll mess up the plastic threads and not get a good seal.

After the new replacement part arrived, I took off the complete back panel (after unplugging the electrical and shutting off the hot & cold water supply). I disconnected both hot & cold water hoses, unscrewed the 2 screws holding the water valve, unplugged the 2 electrical wires for the water valve sending unit, unclamped the outlet water hose. Then I reversed order with new water valve. Put everthing back together in about 20 minutes overall. I did also replace the hot & cold water supply hoses with a better quality hose. Works like new! Thank you very much.

S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.

Remove front cover of stackable washer dryer to expose pump. Remove belt from drum and motor. Remove water lines from pump. Remove motor and pump which is on top of motor. Pump was rusted to shaft of motor which was removed by pry bars. Cleaned shaft with emery cloth and applied never siezed to shaft. Replaced motor. Replaced pump on shaft of motor. Replaced wiring. Replaced hoses. Replaced belt. Replaced hold down clips. Back in service.

I installed this part on a stackable washer-dryer unit. First, I removed the hoses (one had broken off already, damaging the cold water coupling). Using a nut driver I removed the screws on both L-brackets in back that help secure the dryer unit to the washer base. Then, I located 2 other screws securing the dryer to the washer base. These were fairly accessible in the recess where the dryer exhaust vent is located, directly above the water inlet valve. I removed both with a nut driver. I thought I would have to also unscrew 2 more screws on the other side of the dryer, but these were not accessible. So I lifted the side of the dryer I had unbolted to get to the water inlet valve. And voila! It lifted up. I placed a 2x4 on edge to keep the dryer tilted open. The inlet valve is attached to the back inside of the washer by a single screw on the Kenmore, which I removed with a phillips screw driver. Reaching inside the back of the washer, I disconnected the water hose by pinching the retaining clip with pliers. Then I pulled the electrical connections off the the hot and cold solenoids and the unit came out. The replacement unit was installed in reverse.

I removed the front panel to see the belt was snapped in two. The front roller is sping loaded, so I gave it a little tention, slid the belt back on and viola! it was that easy. If your washer starts to vibrate more and sounds louder than normal, get a belt as soon as possible because that may be the problem. Once I put on the new belt, the machine ran as quiet as it did when I first bought it.

I removed the broken knobs and after that it was just plug and play.

I removed the top of the washer by removing two screws on the back. I located and bypassed the lid switch to make sure that wasn't the problem. The problem still existed so I removed the two screws that hold the front panel of the washer. Using a flashlight, I located the drive belt and immediately saw that it was out of position and had pieces missing. I cut and removed the old belt, placed the new belt on the tub pulley and slowly maneuvered it onto the motor drive wheel. I then squeezed the tensioner pulley so that the belt was seated. I turned the timer dial which started the washer and it immediately began pumping the water out of the tub. Problem solved!

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

I used a screwdriver to remove the front of the washing machine, fit the belt around the main pulley, held in the spring loaded tension pulley, and threaded the belt aound. It works great! I really need this inexpensive repair, since my job was downsized, and I can't afford to pay anyone.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

First I made sure the breaker was shut off (220 volts at 50 amps will make short work of anyone). Then I removed the screws for the top of the dryer housing (this is a stacked washer&dryer unit). I was then able to access the limiter although it is a very tight squeeze. The limiter is right next to the connections for the heater element. The limiter is removed by disconnecting the two wires and removing the two screws holding the limiter in place. For both removal and installing it is essential to have a very short, magnetized phillips screwdriver.

Removed the front, door and all. Replaced both upper and lower seals and allowed glue to dry for 24 hours. Removed 3 screws attaching drum to pivot in rear. While drum was out, relubricated pivot seat and ball. Installed new drum which has been re-designed, has strip around entire lip now. Seals are different, so both have to be replaced with ones in kit, supplied tube of glue is not enough to do the job, so used gator glue. Had trouble installing the 3 screws that attach it to the pivot. Finally re-assembled entire front panel and replaced the door. Started the dryer and it worked as new.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.