41797802792 Kenmore Washer Dryer Combo - Instructions

This is a newer washer, but I don't know the age. I just bought the house...!

I made this repair more difficult than it needed to be. I took off the back panel of the machine completely, only to discover the coupling for the hose was near the front of the machine. I tilted the unit on its side and took off the bottom before I discovered the access panel on the front, which is held on by only two screws. I put the bottom panel back on, tilted it upright, took off the panel, and had easy access to the coupling. The new part fit perfectly, and a quick wash load proved the leak was fixed.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

First I did some research and concluded the water inlet needed replacing. Obviously once you know what you need you go to PartSelet.com for parts and installation info. I went through the front of the machine. So I removed the front of the washer(2 screws at the front bottom)slide down the panel to separate it, lifted the top cover of the washer(2 screws on the underside of the lid and 3 wire connectors to the fill switches) and then loosened the right side panel(3 screws at the bottom). Now pushing the wash barrel to the side it gave me enough room to squeeze my arms in to the inlet part. Be careful there are sharp edges and screw tips inside the machine. I removed the 2 wire connectors(hot and cold solenoids) inside the washer and then removed the screw from the back outside that holds the water inlet to the machine. Now I was able to pull the inlet closer to me so I could get pliers on the hose clamp to loosen and remove the old part. The new part was an improved version that was more solid. I attached the hose affixed the squeeze hose clamp and pushed the water inlet into place. The screws were not threading so I grabbed a couple of self taping hex head screws and a nut driver head for my drill and screwed the inlet in from the back of the washer. Then I replaced the wire connectors to the water inlet. With the water inlet complete, I reattached the right side panel, the washer lid, fill switch connectors and the front panel. Washer fixed and running perfectly!

Not having the repair manual made the repair more difficult. Prior experience made the job somewhat easy. Had to study every move to make sure no parts were not broken but overall the repair went without any problems. I found out that the bearing plate was removable to facilitate removal and replacement of the heating element. Advise if you are doing a repair of an appliance you don't know much about, take your time and everything should go well for you.

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.

Removed top,removed hose from inlet valve to washer,removed hot and cold inlet hoses and with phillips screwdriver removed water inlet valve assy and replaced. Reassembled and tested.

My order arrived 2 days after i ordered same. Excellent service from partselect, Thank You....

From previous responses on this site. I just followed their lead. If I had not found these folks, and the responses, it would have been a nightmare. It looked like and I thought the dryer came apart from the back! But in reality it comes apart from the front!! Absolutely fantastic site and help. Fast shipping, I ordered on Wednesday before Labor Day, didn't expect the parts until the following Wednesday, but received the parts on Saturday morning, and had the dryer back running by Sunday AM. Never even ran out of clean clothes!!!!!

I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

removed top and front panel on stackable dyer unit. 3 screws at back of the inside of the drum, and the drum was out. installed new bearing and belt and all was good.

I made my job difficult by removing the back panel, then the side, and finally discovered the front panel opens giving access to the washer. Using heavy pliers I removed the spring clamps and replaced the pump to washer hose and the other hose end to the tub. Turned on the washer no leak only to discover the drain hose had developed a leak. So I ordered the second hose. I was not sure how to release the plastic retaining clamps. Finally just yanked them loose, which worked. Ran the hose through the machine out the back into the drain pipe. I was able to reattach the retaining clamps put the spring clamp on the pump end of the hose. The difficult part was getting the back, sides and front of the washing machine together that took hours.

Removed top cover.
Lowered control assembly.
Removed front door assembly.
Removed drum.
Removed heater assembly.
Removed support bearing and bracket using existing bonding ball.
Re-assembled in reverse order.

All I did was push the new part into the machine! So easy!