11092964101 Kenmore Washer Dryer Combo - Instructions

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

1 screw to replace.

My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggravation!!! AWESOME!!!!

Gary

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.

simple and easy . Just tipped the machine back, pump was right there in the front.
Hardest part was getting the old pump off the shaft. I used a small block of wood & a large screwdrive to pry it loose (gently).

After it came off I filed off some corroded spots on the shaft before slidding on the new one. then its slid on easy,
Snapped on the clips , clamped on the hoses, Done, Momma's Happy, I'am Happy

Ordering was easy, Shipping was fast.
I will use you again.

First I did a search on dryer repair. Found a website that described easy things to check with an ohm-meter. I then performed the continuity checks on the items and found the high-limit one was open, in other words, no good. It works similar to a fuse. All this was done after removing the back panel, just a few screws. The reason it exceeded the high limit, possibly because I never opened the back up and cleaned it. Found out it should be done every couple years. My vent line had a hole in it and was letting lint get drawn into the heating element, could have been a fire.

Took of the back cover, and removed the vent connecting the blower motor to the drum. It was completly full of lint, so cleaned it out completly, and tried the dryer again. The heater element was still cutting off early, and the clothes were not getting very warm, but better than before. Decided to change the thermal cut-off switches. Ordered the parts on Sun, they came in on Tuesday. Dryer was up and running Tuesday night. Just 2 screws per switch, took less than 1/2 hour. The dryer now runs like brand new, and my wife was ready to fork over $800 for a new one!

Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.

The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.

It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.

Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum, let sit a few minutes. Put everything back together.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]

Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.