41799180820 Kenmore Washer Dryer Combo - Instructions

replaced bearing and shaft new belt and everything works just fine

This link provides clear simple instructions which I was able to use successfully.

Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.

Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhesive to glue on the new guide. Use masking tape to hold it while it dried.

Reverse the first paragraph to re-install.

Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.

First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect.
Mike

Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.

took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer

Took it apart and installed the parts. Then I threw the dryer in the trash and bought a new one.

removed top cover to access valve dissconnected hoses and wires then unscrewed valve and replaced

First I raised the top of dryer, then removed 2 screws holding the front of dryer to the sides. removed old drum glide using a putty knife and glued new glide in place with glue provided. replaced front and top. The whole job took about 20 minuets and saved me the cost of new dryer

OK, this is a follow-on repair story.. I *did not* order the lower basket seal when I ordered the upper basket seal... shame!!! BUT, I am now exceptionally quick at removing the front panel - less than 20 seconds!!!

For those who are considering doing this repair, there are more detailed explanations below - my only tip to help do this "quickly" would be to get some automotive brake cleaner to dissolve the old adhesive .. it is AMAZINGLY effective.. The best part is, don't worry about completely removing the old felt when you are tearing it off.. If some is still stuck to the door, it will actually hold some of the brake cleaner in contact with the old adhesive, which accelerates dissolving of the adhesive. Scrape it all off with a plastic scraper, and wipe it down a few times - surface is prepped & ready for the new adhesive + basket seal.. Use spring loaded clamps to hold the seal in place as you install it also.