41794862300 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Luis from La Jolla, CA
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no filter
filter inalled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from San Francisco, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No heat.
As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Emporia, KS
- Parts Used:
- 137513300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Front drum guidesnubber ring was worn out
removed the top of dryer, pulled front panel back from drum and installed snubber(Front Drum guide).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Rochester, NH
- Parts Used:
- 134548800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Leveling Leg Broken
The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installation for DIY. The new legs work great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from lake worth, FL
- Parts Used:
- 137513300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
clothes were getting stuck
after numerous holes put in my families clothes i looked on line and found "partselect.com". i ordered the front drum glide after seeing a similar story about the clothes being torn and getting caught and my family and i have our new dryer back!! yeah :<)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Fairfield, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heat would initially come on then go off or sometimes not come on at all.
1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WASHOUGAL, WA
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out dryer lint screen
Placed new lint filter in proper slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- josef from Nashville, TN
- Parts Used:
- 134511600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer tub was not spinning
Smelled burning rubber, checked belt. Belt was cracked and worn out. Easy repair. Removed front of the machine held together with two screws at the bottom of the unit. Removed top cover of machine (the part with the lid). It just pops off. Pushed tensioner wheel in and took off old belt. Putting new belt on was super easy. Working like a champ now. $20 total with shipping. Not too bad to save a washing machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denis from LONGMEADOW, MA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas dryer would generate heat at the beginning of the cycle but would stop after 5 min and would start making a buzzing noise.
Unplug from electric outlet. Use putty knife to press on two brackets holding the top cover. Raise top cover. Unscrew two screws holding the front panel. Raise front panel up and move to the right (careful with the wires). Disconnect wires from coils. Unscrew two screws holding a small bracket holding the coils. Replace coils and reassemble everything. (HINT: make sure you drum is empty. Mine contained dump clothes, and it turned out front panel actually provides support to the drum, so mine was hanging there with some weight in it - probably not good).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from WOLVERINE, MI
- Parts Used:
- 134511600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Smell of rubber under dryer. Inspection proved belt cracked and shinny worn spot.
Installation was easy, however watch repair instructions video for your model number to easily remove front access panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TJ from SCOTT DEPOT, WV
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Tyngsborough, MA
- Parts Used:
- 131873304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
I pulled off the old knob and replaced it with the new one. The part was very easy to find on your web site. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hudson Falls, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud Squealing
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bayonne, NJ
- Parts Used:
- 131413600
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Dryer drive belt came off dryer drum several times.
Stud was coming off the motor cradle- bad swedge at the factory, Belt tensioner went on stud.
Removed small access panel in back. Remove tensioner and set to left. Remove inner and outer panels from the front of the laundry center to expose exhaust duct and blower. Loosen control panel and remove, disengaging four keyed plugs. Remove lint screen. Loosen two screws inside dryer to disengage exhaust duct and remove, Unscrew aproximately six screws and remove front half of blower. Remove clip from blower shaft, and cautiously pry the blower wheel off the shaft (this is the touchiest part of the job. Some force is necessary). Remove the back half of the blower housing by unscrewing the three screws exposed by the wheel (access through the front) and the standoff by the heat/moisture sensor (access through the back).
You have now exposed the motor. It is held on to the cradle with two clips. Remove the clips by putting your thumb on the clip above the hook and squeeaing while prying the end of the clip off with a screw driver. One clip is accessed through the back and one through the front. When the motor is loose unscrew the two screws through the back panel that keep the cradle in place. Pull it back and remove it, while holding the motor up.
Installation is the reverse. Make sure the new part matches the old part exactly. Make sure that the soft bushings on the motor are centered on the cradle before you clip it in place.
Removed small access panel in back. Remove tensioner and set to left. Remove inner and outer panels from the front of the laundry center to expose exhaust duct and blower. Loosen control panel and remove, disengaging four keyed plugs. Remove lint screen. Loosen two screws inside dryer to disengage exhaust duct and remove, Unscrew aproximately six screws and remove front half of blower. Remove clip from blower shaft, and cautiously pry the blower wheel off the shaft (this is the touchiest part of the job. Some force is necessary). Remove the back half of the blower housing by unscrewing the three screws exposed by the wheel (access through the front) and the standoff by the heat/moisture sensor (access through the back).
You have now exposed the motor. It is held on to the cradle with two clips. Remove the clips by putting your thumb on the clip above the hook and squeeaing while prying the end of the clip off with a screw driver. One clip is accessed through the back and one through the front. When the motor is loose unscrew the two screws through the back panel that keep the cradle in place. Pull it back and remove it, while holding the motor up.
Installation is the reverse. Make sure the new part matches the old part exactly. Make sure that the soft bushings on the motor are centered on the cradle before you clip it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph W from WEST PALM BCH, FL
- Parts Used:
- 134548800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leveling leg sheared off
Put machine on dolly. Tilted it on its back. Put screw driver into sheared leg and unscrewed broken leveling leg. Then screwed new leg in and tilted machine back up.
Was this instruction helpful to you?
Thank you for voting!