41771732811 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cindy from Mauston, WI
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squeeking when ran
Followed online video. All went smooth. Runs great!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kurt from Fargo, ND
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Loud sqweeking after dryer was in operation for over an hour
FOLLOW THE VIDEO!! I was scared to even get into it until I watched the video. Made it easy for me and I have little to no mechanicl skill. Excellent video that made it super easy. Took me an hour as I was taking my time. Now I could probably do the same repair in 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from FELCH, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no heat to dryer at startup
Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from edinboro, PA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
loud scratchy noise
first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from North Aurora, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Burner would not ignite
Unplugged the electricity, turned off the gas, then pop open the top of the dryer. Removed the two screws and pulled the front of the dryer off. Removed the two screws that locked down the two m series ignition coils. Put it back together and all things worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jay from youngstown, OH
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
easy
parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Green River, WY
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
the drum was making wierd sounds like it was a worn out bearing
i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from San Diego, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No heat.
Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from League City, TX
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Loud Squeeking
First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Opelousas, LA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
off balance and noisy operation
removed the drum out the front and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Chicago, IL
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Remove old filter with holes robbing our drying time of efficiency -
Drop in the new beautiful filter without holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Aurora, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Drum Squeeking
Replace the Drum Bearing and Shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- A.J. from katy, TX
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner on for just 10 sec when started.
I tested continuity on parts like burner (ok) then on solenoids (not ok) timer (ok) I visited several websites and found the AppliancePartsPros.com site with FREE repair forum and found valuable advice. Then ordered my parts at Parts Select and were delivered 3 later at my front door.
Now a days you almost can forget to work on all the electronics in a wasmachine and dryer, unless you're a electronic guru.
THks.
Now a days you almost can forget to work on all the electronics in a wasmachine and dryer, unless you're a electronic guru.
THks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Celia from El Paso, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer was tumbling, but not heating or drying clothes
There was a small plate and 2 screws holding the 2 coils. I just removed the screws, unplugged the 2 coils, plugged the new ones in and put the dryer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Hudson, NC
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer ran but no heat.
Followed instructions and the repair went very smooth from start to finish. From getting tools out of tool tray to putting them back it took 15 minutes.
Was this instruction helpful to you?
Thank you for voting!