Models > 11089675100 > Instructions

11089675100 Kenmore Washer Dryer Combo - Instructions

Jump to:

All Instructions for the 11089675100
91 - 105 of 1396
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jayanti from SNELLVILLE, GA
Parts Used:
W10814296
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The middle tub would not come out
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Luis from VALDOSTA, GA
Parts Used:
279173
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The dryer start but it did not stay on.
I replaced the push start buttom,but it still had the same problem,so I went to the motor and found the burnt wire and bingo,we are happy again thanks to your website.
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rebecca from Scarsdale, NY
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer would not start.
Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Russell from Hyannis, MA
Parts Used:
WPW10072840, 80040
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Top section of agitator would not spin.
Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Albert A Little from brookfield, MA
Parts Used:
WP694674, WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
the dryer would run for about two mints and shut off
removed the back of the dryer and the thermal fuse and the dryer cycling thermostat were right next replace them and the dryer work like new my dryer is 40 years old and saved a ton of money fixing it myself
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from Smyrna, TN
Parts Used:
279827
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Start windings burnt out on original motor (dryer would not start)
The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from PELHAM, MA
Parts Used:
W10837625
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Socket set
Broken Motor Pulley
Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge would be thru the roof.
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janice from BLUE SPRINGS, MO
Parts Used:
WPW10250667, 285805
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
1. No hot water and cold water filled very slowly. 2. Washing machine severely vibrated and was very noisy.
EXACTLY as your video demonstrated.
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eddie from Charlotte, NC
Parts Used:
285805
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Washer would not fill with water...
Watched the video on the website... and did what it said to do. It was VERY helpful... It did not fix the problem... so now I'm on to the next possible solution. Also, provided by the website. The valve was the problem 85% of the time. The water level switch is the problem 10% of the time. The water level switch is what I ordered next.
Ordering is EASY and delivery is fast with available tracking of the shipment. Very nice...! -Eddie Campbell
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from HENRY, VA
Parts Used:
285805
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Replacing water inlet valve with new one
The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her)
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Matthew from Wauwatosa, WI
Parts Used:
285320
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
washing machine stuck on drain cycle
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
17 of 41 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Betty from Erie, PA
Parts Used:
279457
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
couldn't get the wire connection anywhere after we bought the heating element.
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from Hull, MA
Parts Used:
W10828351
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
lod and heat caused cracks
replace basket with new one snapped in
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gay from Apple Valley, CA
Parts Used:
W10820036
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Drum would not spin to drain water
Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.
9 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from Oxnard, CA
Parts Used:
WPW10512946, 349241T, WPW10359270, WPW10359269
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The dryer was squeaking and would not heat at all.
The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at first but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11089675100
91 - 105 of 1396