GTUP240EM5WW General Electric Washer Dryer Combo - Instructions

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.

I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes

At first diagnosed the problem watching you tube videos but I did not open the machine. It took awhile to learn the first step to diagnose the issue is to find out if the squeak comes from the front or back of the machine. Mine was in the front. Once I did this I ordered the glides. When they arrived I opened up the machine and found out both the glides and the plastic piece upon which the drum turns and the glides attach were totally shot. I then ordered up that plastic piece. The repair was a breeze. Opening the machine, installing the pieces and closing up took about half an hour max. My reaction is the engineering behind these pieces is not up to par. Seemingly paper thin plastic can't stand up to the constant turning of the drum. As an ordinary consumer I expect much better. The old adage that they don't build em like they used to applies here. I was surprised by what was under the hood as they say. I almost had bought a new machine, and also consulted a repairmen which led me to believe a new machine would be my best option. However, I gave it a shot after doing some internet research and solved the problem for a fraction of the cost. And while I was in there I cleaned out the stray lint!!

First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.

I only had to replace the "plastic" knob on my dryer. This required no tools- just push on to the stem. This part needs to be improved... should be made out of something other than plastic because this gets a lot of wear. I was very pleased with how fast I was able to order & receive my part shipment. I shopped around for this part & your company beat any other price on the market. THANKS!

Removed door strike and latch, replaced, works like new.

easy to fix took less than 10 minutes

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.