GUD24ESSM1WW General Electric Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gene from San Francisco, CA
- Parts Used:
- WE22X35337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grid Slide -3 plactic nubs broken slide was loose.
Take old grid slide and pannel off. Clean lint trap wire framework and replace. Make sure this trap frame fits snug against the door, otherwise it puts pressure on the new slide. This is the second time I have replaced this Grid Slide. Slid new pannel into grid frame. Ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doyon Remote Facilities from Sterling, AK
- Parts Used:
- WH44X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broken lock lid
Replaced with the new part that I ordered from partselect.The washer works good. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from early branch, SC
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clip on door broke
it was easy, it clip right on.needed to give it a little tap to get it in .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Athlynne from Williamsburg, VA
- Parts Used:
- WE09X27634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Frequent Metallic Screeching Sound
Unplug the dryer. On the back, I unscrewed the top three screws that hold on the instrument panel and (from the back) slide the panel to my left to disconnect from the top. I opened the dryer door and removed the two screws on the inside top of the doorway to remove the top panel of the dryer. Inside the top of the dryer are two screws to remove so that I could swing the front panel of the dryer out to replace the lower front felt drum seal. I needed to use wd-40 on these screws. When the panel opens, there is no way to disconnect the wires to remove the panel, so I had to prop it up with something so it didn't tip over and damage the wiring; a sturdy chair worked. Then, I heared the drum pop off and drop down a little. I replaced the seal according to the video; by putting it in the groove and pressing it down into the tabs with a flat head screwdriver or something smooth with a little of the seal hanging over the groove at each end. While I was in there, I cleaned out the lint and the wd-40 I used earlier. Then I closed the panel, lifting the drum back into place, ensuring that the dryer drum would turn before and after I replaced the screws. I replaced the top panel and the screws inside the dryer door and slid the instrument panel back into place and replaced those screws. The dryer works great and very quietly now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teddy from Norwalk, CT
- Parts Used:
- WE22X35337
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The lent filter protector broke
removed broken part and replaced it altogether.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard A. from Little Elm, TX
- Parts Used:
- WD21X10261
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not start
Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Helena, GA
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Needed to change the felt due to a squeaking noise.
I'm a 90 pound mother of 4you and was able to fix this problem all by myself. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Riverview, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The unit would not start.
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Daytona Beach, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would Not Start
Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from martinsville, IN
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer did not latch
easy to fix took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gayle from Philadelphia, MS
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer wasnt drying as fast and was making a lot of noise.
Followed the directions from the video about that particular part. I am 57 and it was fairly simple to do.
Was this instruction helpful to you?
Thank you for voting!