LCG771LL1 Frigidaire Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randall from New Roads, LA
- Parts Used:
- 131825900, 5303281153, 131724301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bearing bad and shaft broken
replaced bearing and shaft new belt and everything works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Thornton, CO
- Parts Used:
- 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
loud squeeling noise
After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from EATON RAPIDS, MI
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer pumps and drains but does not agitate or spin.
Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.
Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.
Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.
I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.
Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.
Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.
I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from PORTAL, GA
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Our door catch got lost inside the dryer after the door was slammed to hard
I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from dallas, TX
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Latch on dryer no longer worked
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.
Was this instruction helpful to you?
Thank you for voting!
door catch wasn't working and screws in door were loose.
popped the catch in existing hole and replaced the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Flemington, WV
- Parts Used:
- 134418700
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
transmission wore out
After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from CENTENNIAL, CO
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Rear Bearing wearing out
I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- April from CARYVILLE, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy
Took it apart and installed the parts. Then I threw the dryer in the trash and bought a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from BROOKLYN, NY
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Just popped the part I ordered right in and it's was closing in no time !
Just opened package and popped the part right in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from tahlequah, OK
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bearing went out
took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Batesburg, SC
- Parts Used:
- 5303207102
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
strike broken
popped in one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohamad from Chicago, IL
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer was not spinning
We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.
I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.
I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Ketchikan, AK
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would only let cold water in,then not fully cycle
Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Unionville, PA
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
over fill caused door to come open
removed top cover to access valve dissconnected hoses and wires then unscrewed valve and replaced
Was this instruction helpful to you?
Thank you for voting!