MLXE42RED5 Frigidaire Washer Dryer Combo - Instructions

-Remove front panel - 2 screws
-Remove the top panel - 2 screws
-Disconnect the lid switch from the top panel - 2 screws
-Remove the agitator cap - unscrew
-Remove the agitator - This was a bit difficult and required a lot of jiggling but it eventually came off
-Remove the inner drum - 5 bolts at the bottom
-Remove the drum mount - 2 bolts and then it got really difficult. A lot of penetrating blaster, wire brushing, jiggling, and some strategically placed hammer taps (don't damage the threads.
-Remove the seal
-Clean up the inner and outer seal seating surfaces
-Rinse and repeat in reverse (pun intended)

Followed your website repair guides and the great belt replacement video.

Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.

Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.

John H.
Palm Desert, CA

The disassembly was very easy and it appeared that this would be a very quick repair. But the removal of the old felt was difficult and once it was removed it took a lot of effort to remove the bits still stuck on. The tool of choice to remove the stuck on felt was a small torch. After that use a coarse sand paper to remove the remnants. Glue on the new felt and reinstall the front panel.

This is a stacked wash/dryer.
- unpluged washer/ dryer
- removed front panels under dryer drum area
- disconedted the wiring connection from washer to dryer
- removed front door panel
- disconnected and removed belt
- removed screws holding in drum
- removed drum
- replaced felt on the door (came with drum replacement kit)
- aligned and attached new drum
- replaced belt on drum
- aligned and installed door
- reconnected wiring connecting washer and dryer
- installed fron panels under dry door
- pluged in washer/dryer
Works like new

Took off all controls and panel. Removed the top. Pulled out the drum. Unscrewed shaft and bearing holder. Replaced all parts and started it back up.
--The parts were shipped timely,

With prep work mentioned below and a good flashlight it takes about 15 to 30 minutes if you're a good handy-man. If you're not, get a neighbor or friend who is. This repair isn't rocket science, but does take a some mechanical aptitude. This unit is a washer/dryer combo unit. Unplug power cord and remove water supply hoses, the drain hose and dryer vent if required to obtain easy access to front panel. There is water in all the lines, so have some towels and a small gallon bucket to help drain the lines if disconnected. Remove two screws on bottom of front panel. Be sure there is about 2 inches from washer/dryer to floor in front to allow front panel to drop directly down, then pull panel out lightly. Wood spacers or similar are recommended under front feet to prop-up front of washer. (There are two tabs on each side of the front panel. The panel must be pulled straight down to clear tabs). Another option is tilt back the washer/dryer about 60 to 75 degrees unit to make the front panel more accessible if all is disconnected in back and you have the room to do so. Once the front panel srews are removed, you may have to place an object (thin pry bar or screw driver) between the top of the washer unit and the front panel for release (be careful not to dent or scratch the top metal or front panel. Remove front panel and set aside. Locate belt near bottom and tensioner pulley (it moves back and forth laterally), push in tensioner pulley to relieve pressure on belt and remove belt from small pully wheel at motor, then the large drum pulley wheel. Place new belt on large pulley first, then small pulley. Push in tensioner pulley and move middle of belt to the inside of the tension pulley to take up the slack. This process is somewhat hard. It takes good hand strength. Be sure the belt is aligned in pulley grooves. Place washer/dryer back in level position, re-attach water supply hoses, drain hose, dryer vent line and power cord, if removed for repair. Check for leaks in water supply lines and be certain the drain hose is well attached to the drain pipe. (This is a good time to clean or replace the dryer vent line to prevent possible lint fires.) Plug in washer/dryer unit and test as if washing a small load. Re-install front panel after successful test in run operation. The part came quickly and fit perfectly.

Remove front lower access panel: two phillips screws at the lower edge then the panel slid down and off. Removed 5/16 pump mounting screws then slid a shallow pan under pump to attempt to catch stale water, removed left side (inlet) hose clamp and wiggled hose off to drain water with some success, some spillage. Removed outlet hose, turned the pump around to remove electrical connection. Reversed steps to mount new pump and after fighting with spring clamp on outlet side I chose to replace that spring clamp with a 1 1/2" stainless hose clamp which then could be tightened with a screwdriver and only took a minute to wrap up.

Disconnect power. Disconnect water hoses. Remove back panel. Remove top panel. Disconnect bladder ring. Disconnect control panel wire harness and control panel. Remove front panel. Disconnect hose clamps to drain hose and tub drain hose. Disconnect pump motor power supply wire. Disconnect pump screws. Now do everything in reverse replacing old pump with new.. One special note: replace factory hose clamps with new hose clamps.

Removed drum replaced bearing with kit, replaced both front drum seals and drive belt. The only problem was when replacing the rear drum ball the three screw holes were poorly tapped and took several tries to get them in. The manufacturers could easily fix this problem. They could provide self tapping hex head screws instead of the Phillips head screws. Everything else went very smoothly.

Don’t do like I did and undo the drummer from the back of that thing pulled off the bearing

no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!

The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installation for DIY. The new legs work great.

Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.

Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.

filter inalled