FLSG72GCS4 Frigidaire Washer Dryer Combo - Instructions

Checked PartSelect online for people with a. similar problem. Found most common problem was the coils.
I opened the top, removed the two screws holding the front panel, unclipped the wiring harness from the machine to the door and removed/cut the plastic wire tie and front came off easily. I put the front piece to the side after changing the light bulb. I cleaned out a large amount of lint and found the coils on the left hand side without trouble. Carefully disconnected the wiring clips, unscrewed the holding screw and removed the old coils. Installed the new colis, 1 has three prongs and the other has 2 so you ca'nt mix them up. Replaced the hold screw, re-connected the witing harness, installed a new wire tie, and re-stalled the two holding screws. Closed the cover and turned it on.
At first it did not heat up which was dissappointing; but then I left it alone and 15 minutes later it worked like new! And heated up just fine ever since.

Total cost about $35.00 with shipping. I took a chance that I would not need the sensor or the ignitor based on the comments of others and I just bought the coils. If I had to do it over I would have bought all three and saved on the shipping.

Took off all controls and panel. Removed the top. Pulled out the drum. Unscrewed shaft and bearing holder. Replaced all parts and started it back up.
--The parts were shipped timely,

First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!

The disassembly was very easy and it appeared that this would be a very quick repair. But the removal of the old felt was difficult and once it was removed it took a lot of effort to remove the bits still stuck on. The tool of choice to remove the stuck on felt was a small torch. After that use a coarse sand paper to remove the remnants. Glue on the new felt and reinstall the front panel.

Followed your website repair guides and the great belt replacement video.

Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.

Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.

John H.
Palm Desert, CA

Removed drum replaced bearing with kit, replaced both front drum seals and drive belt. The only problem was when replacing the rear drum ball the three screw holes were poorly tapped and took several tries to get them in. The manufacturers could easily fix this problem. They could provide self tapping hex head screws instead of the Phillips head screws. Everything else went very smoothly.

With prep work mentioned below and a good flashlight it takes about 15 to 30 minutes if you're a good handy-man. If you're not, get a neighbor or friend who is. This repair isn't rocket science, but does take a some mechanical aptitude. This unit is a washer/dryer combo unit. Unplug power cord and remove water supply hoses, the drain hose and dryer vent if required to obtain easy access to front panel. There is water in all the lines, so have some towels and a small gallon bucket to help drain the lines if disconnected. Remove two screws on bottom of front panel. Be sure there is about 2 inches from washer/dryer to floor in front to allow front panel to drop directly down, then pull panel out lightly. Wood spacers or similar are recommended under front feet to prop-up front of washer. (There are two tabs on each side of the front panel. The panel must be pulled straight down to clear tabs). Another option is tilt back the washer/dryer about 60 to 75 degrees unit to make the front panel more accessible if all is disconnected in back and you have the room to do so. Once the front panel srews are removed, you may have to place an object (thin pry bar or screw driver) between the top of the washer unit and the front panel for release (be careful not to dent or scratch the top metal or front panel. Remove front panel and set aside. Locate belt near bottom and tensioner pulley (it moves back and forth laterally), push in tensioner pulley to relieve pressure on belt and remove belt from small pully wheel at motor, then the large drum pulley wheel. Place new belt on large pulley first, then small pulley. Push in tensioner pulley and move middle of belt to the inside of the tension pulley to take up the slack. This process is somewhat hard. It takes good hand strength. Be sure the belt is aligned in pulley grooves. Place washer/dryer back in level position, re-attach water supply hoses, drain hose, dryer vent line and power cord, if removed for repair. Check for leaks in water supply lines and be certain the drain hose is well attached to the drain pipe. (This is a good time to clean or replace the dryer vent line to prevent possible lint fires.) Plug in washer/dryer unit and test as if washing a small load. Re-install front panel after successful test in run operation. The part came quickly and fit perfectly.

Raise the top and remove the front panel assembly. One philips screw, 24mm gas line coupler and 3 electrical connectors frees the burner assembly. Slid the old igniter out and the new one in.2 philips screws to remove the coil retainer and replace the coils.

I first thought I needed to purchase a new washer/dryer and in fact, I ordered new appliances. But then I tried using pliers to set the timing on the dryer and was able to get the dryer to work and thought I'd try to buy a new knob. I cancelled the order for the new washer/dryer and in several days I received the replacement part. The new part worked perfectly and instead of spending $1,800 for a new washer/dryer, my 15 year old appliance worked perfectly. All I had to do was put the new knob in place (no tools required!) and I was all set. Very happy with my purchase. The knob, including shipping, handling & tax cost close to $50, but it was much better than spending $1,800!

1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)

The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installation for DIY. The new legs work great.

no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!

As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.

filter inalled

Installation was easy, however watch repair instructions video for your model number to easily remove front access panel.