FLSG72GCSTA Frigidaire Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Rahway, NJ
- Parts Used:
- 3204425
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Belt not tight
Tensioner (pulley spring) replacement.
The whole tub and motor are suspended by springs so I just got a flat bar and using the edge of the bottom of the washer as a fulcrum, lifted the whole thing enough to be able to shove a 2x4 under there at the base of the dome. It was still tight getting the lock washer off the bottom of the spring axel, but it popped off by pushing the ends with two screwdrivers.
The whole tub and motor are suspended by springs so I just got a flat bar and using the edge of the bottom of the washer as a fulcrum, lifted the whole thing enough to be able to shove a 2x4 under there at the base of the dome. It was still tight getting the lock washer off the bottom of the spring axel, but it popped off by pushing the ends with two screwdrivers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Huntingdon, PA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Dryer wasn't heating
Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Houston, TX
- Parts Used:
- 134138200
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The rim that supports the front of the drum had worn through, due to my failure to replace the glide styrips in time.
There are only three screws holding the drum in. However, to get it out I had to remove the front panels, and the top of the dryer part of the washer-dryer combo. The drum came out easily, but getting the new one in was pretty hard. I had to guess how the drive belt was routed around the motor pulley and idler pulley, since I couldn't see it until I'd removed the drum. Since the new drum wasn't exactly like the old one, I had to remove the glide strip from the front panel to get it to fit. At present, the unit is not completely reassembled, so I can't say I've been entirely successful. Tomorrow, I will put it back together, cross my fingers, and switch it on. Wish me luck!
Followup: The dryer part of this washer-dryer combo is back online. At first, the dryer made a squealing noise, but eventually quieted down. At present, the drum replacement seems to be just fine. It cost about $215, and, except for a few cuts due to sharp-edged metal, a dropped clip that disappeared into the depths of the bottom of the washer, it is actually REPAIRED. I could have used more specific help, but, all in all, it has been pretty easy, and pretty effective.
Followup: The dryer part of this washer-dryer combo is back online. At first, the dryer made a squealing noise, but eventually quieted down. At present, the drum replacement seems to be just fine. It cost about $215, and, except for a few cuts due to sharp-edged metal, a dropped clip that disappeared into the depths of the bottom of the washer, it is actually REPAIRED. I could have used more specific help, but, all in all, it has been pretty easy, and pretty effective.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Brewster, MA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer tub stopped spinning and was real noisy
I read the last three peoples experiences when I ordered the part on your on line page. I had already made all the wrong mistakes taking the machine apart, and couldn't beleive how simplified it was on your web site. I had called a local repair shop only to be advised the part would take 4 days shipping and the price of it plus shipping was twice what I paid you. Your part arrived the day after I ordered it on line, Thanks again for being there!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Baylis, IL
- Parts Used:
- 137292700, 5303937189
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Motor locked up and started smoking
Unplugged unit. Proceeded to remove front and back covers. Took drum unit out after loosening belt, unplugged wire plug from motor. Removed belt tightening unit. Removed screws holding motor to plate. Took lint catcher unit out of front then removed motor and fan unit combination through front. Reversed procedure. Mounted fan combo motor unit. Put drum in place at front and suspended back part of drum with homemade wire hook. Put belt around drum, then put back cover back in place, removed wire hook and secured back panel. Installed belt tightened. Put lint catcher unit in. Replaced front covers. Procedure was challenging since dryer was part of stack unit. Probably could have left lint catcher unit in and just removed motor fan unit from back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Honesdale, PA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Belt
Very easy to install. Unscrew 2 screws and I was done in minutes. Thanks for the fast part delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from PINCKNEY, MI
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer did not drain, would not cycle; pump was 'humming' and not moving water
Remove front lower access panel: two phillips screws at the lower edge then the panel slid down and off. Removed 5/16 pump mounting screws then slid a shallow pan under pump to attempt to catch stale water, removed left side (inlet) hose clamp and wiggled hose off to drain water with some success, some spillage. Removed outlet hose, turned the pump around to remove electrical connection. Reversed steps to mount new pump and after fighting with spring clamp on outlet side I chose to replace that spring clamp with a 1 1/2" stainless hose clamp which then could be tightened with a screwdriver and only took a minute to wrap up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Oakford, IL
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Pump motor made humming noise and wouldn't drain water from tub.
Disconnect power. Disconnect water hoses. Remove back panel. Remove top panel. Disconnect bladder ring. Disconnect control panel wire harness and control panel. Remove front panel. Disconnect hose clamps to drain hose and tub drain hose. Disconnect pump motor power supply wire. Disconnect pump screws. Now do everything in reverse replacing old pump with new.. One special note: replace factory hose clamps with new hose clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bergenfield, NJ
- Parts Used:
- 5303931775
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Not enough heat
Checked PartSelect online for people with a. similar problem. Found most common problem was the coils.
I opened the top, removed the two screws holding the front panel, unclipped the wiring harness from the machine to the door and removed/cut the plastic wire tie and front came off easily. I put the front piece to the side after changing the light bulb. I cleaned out a large amount of lint and found the coils on the left hand side without trouble. Carefully disconnected the wiring clips, unscrewed the holding screw and removed the old coils. Installed the new colis, 1 has three prongs and the other has 2 so you ca'nt mix them up. Replaced the hold screw, re-connected the witing harness, installed a new wire tie, and re-stalled the two holding screws. Closed the cover and turned it on.
At first it did not heat up which was dissappointing; but then I left it alone and 15 minutes later it worked like new! And heated up just fine ever since.
Total cost about $35.00 with shipping. I took a chance that I would not need the sensor or the ignitor based on the comments of others and I just bought the coils. If I had to do it over I would have bought all three and saved on the shipping.
I opened the top, removed the two screws holding the front panel, unclipped the wiring harness from the machine to the door and removed/cut the plastic wire tie and front came off easily. I put the front piece to the side after changing the light bulb. I cleaned out a large amount of lint and found the coils on the left hand side without trouble. Carefully disconnected the wiring clips, unscrewed the holding screw and removed the old coils. Installed the new colis, 1 has three prongs and the other has 2 so you ca'nt mix them up. Replaced the hold screw, re-connected the witing harness, installed a new wire tie, and re-stalled the two holding screws. Closed the cover and turned it on.
At first it did not heat up which was dissappointing; but then I left it alone and 15 minutes later it worked like new! And heated up just fine ever since.
Total cost about $35.00 with shipping. I took a chance that I would not need the sensor or the ignitor based on the comments of others and I just bought the coils. If I had to do it over I would have bought all three and saved on the shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from STATEN ISLAND, NY
- Parts Used:
- 137221600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The water did not drain at all . You could hear the pump spinning , but it was not .
After making sure there was no blockages and the pump was not jammed I knew it was time for a new one . Unplug the machine and turn off the hot and cold water . Remove the two screws on the bottom of the front of the machine and push down on the panel it should come right off . Make sure all the water is drained out of the tub use a wet/dry vacuum to suck out all the water if needed . Then with the vacuum empty squeeze the clamps that hold the hoses on the pump and push them out of the way . Use the vacuum to suck up any leftover water, as you remove both hoses . Unplug the one set of wires going to the pump . Remove both screws and the pump should now be loose . Do the same thing in reverse to install the new pump . Other than dealing with the water it should take under 15 minutes . Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Reisterstown, MD
- Parts Used:
- 137292700, 5303281153, 5303281153, 131825900, 5303281153, 131724301
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Loud Squeaking c/c unlevel. Led to shaft breaking
Took off all controls and panel. Removed the top. Pulled out the drum. Unscrewed shaft and bearing holder. Replaced all parts and started it back up.
--The parts were shipped timely,
--The parts were shipped timely,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miles from LaPorte, IN
- Parts Used:
- 5303281153
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Loud Squeek while the dryer is running.
1. After checking the Parts Select website for some useful information I unplugged the dryer.
2. I popped the two clips holding the top down and lifted the top up and out of the way.
3. I used the 8mm socket and screwdiver combo to remove the two screws holding the front of the dryer on. These screws are so close to the sides of the dryer that you need something very thin to seat the socket, it is so thin a small rachet would not fit.
4. Once the to screws are free to forget to unhook the two wires that lead to the automatic cutoff switch on the right. Label them and move them out of the way.
5. The front of the dryer should pivot forward and come right off. Don't forget about the two clips at the bottom, they are not really attached to anything and can be easy to lose.
6. Get your screwdriver and dive into the drum, on the back should be three screws, take those out.
7. Spin the dryer around and take off the vent cover in the lower left corner of the back of the dryer, watch out the socket is a smaller size.
8. Once inside there is an idler pulley like on the back of a ten speed bike, pull the tension out of it and take the drive belt off the pulleys.
9. The drum should be able to be pulled out the front of the dryer, set aside with the door. The screws on my dryer were so tight I had to use a hammer drill to remove them.
10. This is were I got stuck, no one mentioned how to get the bearing plate off, as if everyone would just know. You must lift up on the bearing plate and once it moves up then you can pull it out.
11. Use the 8mm socket to unscrew the old plastic bearing guide. The small metal clip on the back of the dryer will fall off with the grounding ball bearing.
12. With brum bearing kit in hand start off by putting as much high temp lubricant as you can into the bottom of the new bearing guide. I also use a little lubricant like glue to hold the new grounding ball bearing in the little hole on the back of the bearing guide.
13. Here is the tricky part you have to screw the bearing guide into the the dryer while simulaneously holding the little metal clip in place on the back of the dryer. I used duct tape to hold the metal clip and once the screws got started I just took the tape off.
14. Now you have to do the impossible, the bearing must be screwed to the drum. So unless you have 7 foot long arms you can't hold the bearing and drive the screws. Another problem is the bearing itself, the holes are not the same size as the original and they are not threaded. I stripped every screw that came with the kit trying to get them through the metal of the bearing.
15. With an unwilling victim holding the bearing steady I finally got a replacement screw to seat through the bearing. Once you get one the rest are easier.
16. You are ready to reassemble, after vacuuming everything ou, pick up the drum making sure the belt is around the drum about where it was when you took it off. Push the drum through the front of the dryer all the way to the back, aim a little high so the bearing can move down and seat in the bearing guide.
17. Tuck the clips on the front panel of the dryer into the bottom front edge of the dryer and the whole front should pivot up, when you get it almost closed you will have to lift the drum and set it on the front bearing in the door.
18. While holding the front of the dryer on you have to reach inside and get the 8mm screw started on the left or right, if you let go the front of the dryer will pop off and you have to start over with the pivot. Now is a good time to have a magnet on a stick so when you drop the screw or screw driver you don't have to take the front off to retrieve your tools.
19. Once the front is on reconnect the two wires to the switch in the front of the dryer. Remember the ones you were supposed to have labeled earlier.
20. Close the top of the dryer and spin the dryer around so you can reach inside the vent door and pull the tension pulley over and reseat the drive belt. Rem
2. I popped the two clips holding the top down and lifted the top up and out of the way.
3. I used the 8mm socket and screwdiver combo to remove the two screws holding the front of the dryer on. These screws are so close to the sides of the dryer that you need something very thin to seat the socket, it is so thin a small rachet would not fit.
4. Once the to screws are free to forget to unhook the two wires that lead to the automatic cutoff switch on the right. Label them and move them out of the way.
5. The front of the dryer should pivot forward and come right off. Don't forget about the two clips at the bottom, they are not really attached to anything and can be easy to lose.
6. Get your screwdriver and dive into the drum, on the back should be three screws, take those out.
7. Spin the dryer around and take off the vent cover in the lower left corner of the back of the dryer, watch out the socket is a smaller size.
8. Once inside there is an idler pulley like on the back of a ten speed bike, pull the tension out of it and take the drive belt off the pulleys.
9. The drum should be able to be pulled out the front of the dryer, set aside with the door. The screws on my dryer were so tight I had to use a hammer drill to remove them.
10. This is were I got stuck, no one mentioned how to get the bearing plate off, as if everyone would just know. You must lift up on the bearing plate and once it moves up then you can pull it out.
11. Use the 8mm socket to unscrew the old plastic bearing guide. The small metal clip on the back of the dryer will fall off with the grounding ball bearing.
12. With brum bearing kit in hand start off by putting as much high temp lubricant as you can into the bottom of the new bearing guide. I also use a little lubricant like glue to hold the new grounding ball bearing in the little hole on the back of the bearing guide.
13. Here is the tricky part you have to screw the bearing guide into the the dryer while simulaneously holding the little metal clip in place on the back of the dryer. I used duct tape to hold the metal clip and once the screws got started I just took the tape off.
14. Now you have to do the impossible, the bearing must be screwed to the drum. So unless you have 7 foot long arms you can't hold the bearing and drive the screws. Another problem is the bearing itself, the holes are not the same size as the original and they are not threaded. I stripped every screw that came with the kit trying to get them through the metal of the bearing.
15. With an unwilling victim holding the bearing steady I finally got a replacement screw to seat through the bearing. Once you get one the rest are easier.
16. You are ready to reassemble, after vacuuming everything ou, pick up the drum making sure the belt is around the drum about where it was when you took it off. Push the drum through the front of the dryer all the way to the back, aim a little high so the bearing can move down and seat in the bearing guide.
17. Tuck the clips on the front panel of the dryer into the bottom front edge of the dryer and the whole front should pivot up, when you get it almost closed you will have to lift the drum and set it on the front bearing in the door.
18. While holding the front of the dryer on you have to reach inside and get the 8mm screw started on the left or right, if you let go the front of the dryer will pop off and you have to start over with the pivot. Now is a good time to have a magnet on a stick so when you drop the screw or screw driver you don't have to take the front off to retrieve your tools.
19. Once the front is on reconnect the two wires to the switch in the front of the dryer. Remember the ones you were supposed to have labeled earlier.
20. Close the top of the dryer and spin the dryer around so you can reach inside the vent door and pull the tension pulley over and reseat the drive belt. Rem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from DACULA, GA
- Parts Used:
- 5303279394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Leaking through the main tub seal
-Remove front panel - 2 screws
-Remove the top panel - 2 screws
-Disconnect the lid switch from the top panel - 2 screws
-Remove the agitator cap - unscrew
-Remove the agitator - This was a bit difficult and required a lot of jiggling but it eventually came off
-Remove the inner drum - 5 bolts at the bottom
-Remove the drum mount - 2 bolts and then it got really difficult. A lot of penetrating blaster, wire brushing, jiggling, and some strategically placed hammer taps (don't damage the threads.
-Remove the seal
-Clean up the inner and outer seal seating surfaces
-Rinse and repeat in reverse (pun intended)
-Remove the top panel - 2 screws
-Disconnect the lid switch from the top panel - 2 screws
-Remove the agitator cap - unscrew
-Remove the agitator - This was a bit difficult and required a lot of jiggling but it eventually came off
-Remove the inner drum - 5 bolts at the bottom
-Remove the drum mount - 2 bolts and then it got really difficult. A lot of penetrating blaster, wire brushing, jiggling, and some strategically placed hammer taps (don't damage the threads.
-Remove the seal
-Clean up the inner and outer seal seating surfaces
-Rinse and repeat in reverse (pun intended)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Plymouth, ME
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Worn front drum slides
The disassembly was very easy and it appeared that this would be a very quick repair. But the removal of the old felt was difficult and once it was removed it took a lot of effort to remove the bits still stuck on. The tool of choice to remove the stuck on felt was a small torch. After that use a coarse sand paper to remove the remnants. Glue on the new felt and reinstall the front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Rochester, NY
- Parts Used:
- 134138200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The lip on the front of the drun separated from the drum
This is a stacked wash/dryer.
- unpluged washer/ dryer
- removed front panels under dryer drum area
- disconedted the wiring connection from washer to dryer
- removed front door panel
- disconnected and removed belt
- removed screws holding in drum
- removed drum
- replaced felt on the door (came with drum replacement kit)
- aligned and attached new drum
- replaced belt on drum
- aligned and installed door
- reconnected wiring connecting washer and dryer
- installed fron panels under dry door
- pluged in washer/dryer
Works like new
- unpluged washer/ dryer
- removed front panels under dryer drum area
- disconedted the wiring connection from washer to dryer
- removed front door panel
- disconnected and removed belt
- removed screws holding in drum
- removed drum
- replaced felt on the door (came with drum replacement kit)
- aligned and attached new drum
- replaced belt on drum
- aligned and installed door
- reconnected wiring connecting washer and dryer
- installed fron panels under dry door
- pluged in washer/dryer
Works like new
Was this instruction helpful to you?
Thank you for voting!