FLSE72GCSB Frigidaire Washer Dryer Combo - Instructions

1. watched PartSelect video 2. adjust for the fact this was a dryer over top a washer. 3. we were able to remove the very top plate of the dryer and not have to remove the drum to get to the Thermal Limiter. 4. i used a drill driver with a square bit to speed up getting out screws. 5. It requires a ladder to be able to work from the top and 6. some pretty good manual dexterity to get the limiter out without removing drum. 7. the replacement seems to have improved the drying function!

I put a new lint filter,that was the problem,just open the dyer door,remove the old filter and put the new one.Fit perfect!!

I watched the videos on this excellent website first. Then the repair was a breeze.

Had a loud noise coming from 10 yr old Kenmore stackable washer & dryer set. Pulled apart and found the dryer drum bearing shot. Ordered the rear drum bearing kit that included the male piece that attaches to the drum (Sears wanted 40.00 for just this part).The kit along with a new belt I installed while I was in there was only 37.00 including shipping. Got parts in 2 days from Chicago to Atlanta! Took about an hour to do the job Video was great. Dryer is very quiet now. However I should have replaced the heater coils while I was in there (40.00) Its the only thing left to go bad at this point. Oh well if it does I will order from Parts Select again and sink another hour into it.. Sure beats a 2-3 hundred dollar service call!!

Removed the front of dryer and cleaned lint and sand removed tub replaced the belt and bearing and she was ready to go Replaced the belt as a precaution since the unit was apart. My skills as a HVAC tech was helpful in making the repair. Parts arrived just as stated. Regular postage...in a timely manner

I followed the instruction video and easily removed the drum. Mine is a gas unit, so the best access to loosen the pulley and belt is by removing a small hatch on the back of the dryer. Removing the ball shaft was initially difficult, since the screws had been stripped by the previous repair person. To solve this, I used a vise-grips to turn the protruding shafts of the screws at the drum rear, and unscrewed them partially out from behind. Once loosened, I used a screwdriver to easily finish them. The old bearing was actually gouged, and there was no lubrication at all in the retainer cup. The job took 2+ hours, since I also replaced the upper felt glider and spent 30+ minutes vacuuming the dryer out.

It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.

installed the back bearing with the ball bearing and dropped in the rear drum bearing and tried to install the drum to the rear drum bearing, but we could not find the screw holes to attach the drum, we tried and tried and finally I came up with the idea to take the drum out and screw the drum bearing while we had it ouside and that worked out beautifu lyl and all we had to do was reinstall the drum and all we had to do was lift it up just a little and drop it into the retainer rear retainer' and then all we had to do was install the tension roller which we had a little trouble but we finally figured it out and now it works just fine, it would a lot if there was a diasgram included on how to re-install the tensioner

This video by Steve Ash was spot on . In our case the white rear support bearing had melted and reformed around the shaft, preventing us from being able to pop the drum in the way described in the video. We used pliers to unscrew the screws on the rear clip from the back of the dryer. The rest of it worked exactly as described in the video. Our model was White-Westinghouse DE600ADD1, which is not a model listed on the PartsSelect website. However the part worked very well. The dryer runs really quite now.

The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning properly. Having to make a new mounting plate was an unexpected adventure!

lifed the lid .remove oud hose and replaced with new hose

Took the old one out, put the new one in! (:>}

watched the video My dryer was a little different but it came apart easily and was an easy fix. My wife did it all by herself.

Really ,no repair;just put new lint basket in dryer;took seconds.