LG600AXW1 Frigidaire Washer Dryer Combo - Instructions

The appliance is gas, which made me a little nervous. However, knowing that I had the gas off, I carefully began disassembly. The burner unit is a very simple set up and within a few minutes I had the entire assembly out and noticed that in fact the igniter was broken. I ordered a new one from partselect.com and it was delivered in 2 days! The worst part of the assembly was when I accidentally bumped the new igniter against the underside of the dryer and broke the brand new one!!!..So, I ordered a second igniter and 2 days later installed it in about 30 minutes.

This is a washer/ dryer combo unit. Start at the top of the unit. Remove top plate then remove cover between dryer and washer. Remove control panel. Now remove front panel with dryer door. Unplug harness connector. With area now open put on new belt around drum and motor. Be sure you put belt around idler pulley correct way so there is tension on belt. Put back together in reverse order. Took me about 40 minutes since I cleaned and vacuumed out appliance.

Smelled burning rubber, checked belt. Belt was cracked and worn out. Easy repair. Removed front of the machine held together with two screws at the bottom of the unit. Removed top cover of machine (the part with the lid). It just pops off. Pushed tensioner wheel in and took off old belt. Putting new belt on was super easy. Working like a champ now. $20 total with shipping. Not too bad to save a washing machine.

I push the new knob onto the post that fit the knob

Placed new lint filter in proper slot.

Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)

Installation was easy, however watch repair instructions video for your model number to easily remove front access panel.

I definitely would not have tried to do this had it not been for the other testimonials written here. But it sounded so easy, I had to just try it (the repair man estimated that with parts and labor, we would be looking at somewhere between $250 and $300!).

The repair itself took less than 15 min, but I spend a good deal of time looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.

It works!!!

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

Just put the new one in the slot the old one was in

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect.
Mike

Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)