FLSG72GCT7 Frigidaire Washer Dryer Combo - Instructions

This repair is realy very easy
As discribed by the others

All I did was push the new part into the machine! So easy!

1 Unplug the dryer and Raise top up by releasing the clips and fold back to expose the drum. 2. Take Phillips head screw driver and remove two screws inside the front dryer panel and then take flathead screwdriver to pop out both sides and set aside. 3. Lay on your stomach and reach inside to the belt pulley and push right so the belt will release then stand to either side of dryer and grab the belt and lift the drum up out of its bracket. 4. Go to the front and pull the drum out and replace the Rear Drum Bearing Kit . 5. Grab the front panel and remove the Top dryer guide and replace to match evenly with the bottom dryer guide by cutting at least 1/8 -1/4" from felt and use High temp adhesive to glue down. 6. Replace everything in order that was taken apart and reconnect electrical plug and start dryer.

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

Customer responses / directions were great nothing to add - except no where does anyone mention "high temperature grease" for the Drum Support Bearing - only on the video is it mentioned numerous times. I honestly think it took longer to vacuum out all the lint then it did to do the repairs.

Very easy to install. Unscrew 2 screws and I was done in minutes. Thanks for the fast part delivery!

Tensioner (pulley spring) replacement.

The whole tub and motor are suspended by springs so I just got a flat bar and using the edge of the bottom of the washer as a fulcrum, lifted the whole thing enough to be able to shove a 2x4 under there at the base of the dome. It was still tight getting the lock washer off the bottom of the spring axel, but it popped off by pushing the ends with two screwdrivers.

Unplugged unit. Proceeded to remove front and back covers. Took drum unit out after loosening belt, unplugged wire plug from motor. Removed belt tightening unit. Removed screws holding motor to plate. Took lint catcher unit out of front then removed motor and fan unit combination through front. Reversed procedure. Mounted fan combo motor unit. Put drum in place at front and suspended back part of drum with homemade wire hook. Put belt around drum, then put back cover back in place, removed wire hook and secured back panel. Installed belt tightened. Put lint catcher unit in. Replaced front covers. Procedure was challenging since dryer was part of stack unit. Probably could have left lint catcher unit in and just removed motor fan unit from back.

I read the last three peoples experiences when I ordered the part on your on line page. I had already made all the wrong mistakes taking the machine apart, and couldn't beleive how simplified it was on your web site. I had called a local repair shop only to be advised the part would take 4 days shipping and the price of it plus shipping was twice what I paid you. Your part arrived the day after I ordered it on line, Thanks again for being there!!!!!

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.

Checked PartSelect online for people with a. similar problem. Found most common problem was the coils.
I opened the top, removed the two screws holding the front panel, unclipped the wiring harness from the machine to the door and removed/cut the plastic wire tie and front came off easily. I put the front piece to the side after changing the light bulb. I cleaned out a large amount of lint and found the coils on the left hand side without trouble. Carefully disconnected the wiring clips, unscrewed the holding screw and removed the old coils. Installed the new colis, 1 has three prongs and the other has 2 so you ca'nt mix them up. Replaced the hold screw, re-connected the witing harness, installed a new wire tie, and re-stalled the two holding screws. Closed the cover and turned it on.
At first it did not heat up which was dissappointing; but then I left it alone and 15 minutes later it worked like new! And heated up just fine ever since.

Total cost about $35.00 with shipping. I took a chance that I would not need the sensor or the ignitor based on the comments of others and I just bought the coils. If I had to do it over I would have bought all three and saved on the shipping.

First, I unplugged the washer then removed the front panel to the washing machine, then the pump cover, then the two hoses connected to the pump, draining them into a small bowl. I removed the ground wire and electrical connections.

Then I removed the two bolts holding down the pump and removed it. I had to pivot the hose connections on the pump to match the old one. Once I did this, I removed the hold-down bracket from the old pump and installed it on the replacement pump.

Getting the hoses clamped back on the new pump was a challenge, and I finally used an automotive clamp on the rear hose. Once the hoses were connected, I bolted the pump back in, reconnected the power and ground connections and replaced the cover.

Overall, it was a fairly straightforward installation and the only challenging part was the hose clamps.

Took off all controls and panel. Removed the top. Pulled out the drum. Unscrewed shaft and bearing holder. Replaced all parts and started it back up.
--The parts were shipped timely,

The disassembly was very easy and it appeared that this would be a very quick repair. But the removal of the old felt was difficult and once it was removed it took a lot of effort to remove the bits still stuck on. The tool of choice to remove the stuck on felt was a small torch. After that use a coarse sand paper to remove the remnants. Glue on the new felt and reinstall the front panel.

Followed your website repair guides and the great belt replacement video.

Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.

Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.

John H.
Palm Desert, CA