LCE772LL1 Frigidaire Washer Dryer Combo - Instructions

popped in one in

Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.

removed top cover to access valve dissconnected hoses and wires then unscrewed valve and replaced

Took it apart and installed the parts. Then I threw the dryer in the trash and bought a new one.

Just opened package and popped the part right in!

took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer

replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!

Remove top cover and front and remove drum and install a new bearing kit and new belt.

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

Watched Video Provided. Very Simple Repair. Asked my lovely wife to hold drum in place while replacing drive belt. She gladly complied and is back doing what she seems to love most. And no, I'm not kidding. Our washer and dryer seem to run 24/7/365. I've completed various repairs on both appliances over the last couple of years and saved 100's of dollars thanks to this site .

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

Just like in the video, but with a stackable washer/dryer unit, works like new now....

First I unplugged the dryer. Then I gently pryed the top of the dryer. This was done from the front using a flat screw driver. Do this gently pushing up on the handle of the tool. It will pop up one side at a time. No need to remove the screws and clips on the the rear top of the dryer. Set the top aside. Then from the inside front of the dryer using a phillips screw driver I removed two screws, one on each side. This allowed me to lift the front of the dryer up and away from the unit, off the two clips on the bottom front of the unit. I set the front cover on top of the dryer. There is no need to disconnect any wires. Next removed the rear vented cover on the back of the dryer so I could acess the belt pullies. From here I pushed the upper left pully to the right to ease belt tension and take the belt off that pully. Slide the belt to the rear of the drum. Next I removed the three screws from the center most part of the inside of the dryer drum. My dryer required the use of a square head driver tool. This allowed me to easily bring the dryer drum out the front of the unit. Set it out of your way. Then I vacuumed the dust out of the dryer. Then I lifted out the metal part that resembles a trailer hitch which had been attached to the dryer drum. Next using a nut driver I removed the two screws which hold the white plastic part of the bearing assembly to the rear of the dryer. That is all the taking apart work.
Putting it all back together was not too difficult. First install the new white plastic part of the bearing assmbly inside the dryer along with the metal part on the outside rear. The little metal ball bearing goes on the OUTSIDE between the little metal part and the rear wall of the dryer. Do not leave it out as it provides electrical grounding between the dryer drum and the body of the dryer. Next attach the new bearing part that looks like a trailer hitch to the rear of the dryer drum. This is the three screw part. Then lift the drum back into the dryer. Do not yet set the drum all the way in. The dryer belt must be looped around the drum. I installed a new belt. If the bearing is worn out it is time for a new belt. The smooth side of the belt goes against the dryer drum. Now apply a generous amout of lubricant to the white plastic cradle which was installed on the back of the dryer and to the ball bearing area. Then the dryer drum may be set into place, that is the trailer hitch part into the white plastic cradle. Now the front of the dryer may be reinstalled. Push up on the inside of the dryer drum to line everything back up. Put the two screws back which hold the dryer front on. Be carefull not to drop them inside. Put the dryer belt back into place on its pullies. It goes on the inside of the left and right pullies and on the outside (bottom) of the pully of the dryer motor. Check for and undo any twists. Plug in and test the dryer. All should be well. Reinstall the rear vented cover. Replace the top, connecting the rear first. Make sure to reattach the green grounding wire. Then push the front of the top down onto its clips. You are done! This took me 1 hour and 10 minutes. It sounds like alot but you can do it! Empower yourself!