GLET1041AS1 Frigidaire Washer Dryer Combo - Instructions

removed the screws, disconnected the wires. installed the new elements replaced the wires.

Removed two screws at bottom of front panel, removed front panel. Used pliers to remove hose clamp on drain hose. Fished hose out of chassis and installed new hose. Tested for leaks.

Disconnect water and electricity.
Shop-vac out the water in the internal drain hose.
Remove back cover, tip washer on side to gain access.
Un-clamp rubber drain hose,unscrew pump and remove.
Cleanout filter cup (yuk!) find coins and hairpins.
Attach drain hose to new pump and re-install with hose clamps from hardware store because spring clamps were impossible (arthritis in fingers).
Reconnect water and electricity.
Test for leaks and tighten clamps if necessary.

The cat was not used for mechanical advantage. Rather he was present for worker's safety regulations. He is a bit of a tool though.

Firstly, I removed the knob from the packaging. Secondly, I stuck it on the peg.

I am not a professional repair person and do not condone or recommend any of the methods used during this repair procedure. The views and opinions expressed in this repair story are for entertainment purposes only.

Had to trial and error my way to getting the control panel off. The parts diagrams on this site were very helpful, but didn't tell the entire story. Started to pull the entire front dryer panel off then found that only needed to remove two panel screws to gain access to all the screws holding the control panel on. With those removed the panel came off as a unit and was easily disassembled. Screws securing the switches are easlily stripped, so be careful. Rest of job was just pulling off wiring clips and reattaching. Everything went back together easily.

The problem with my very old washer was that the tension spring had broken long ago and I had jerry-rigged it in place with a cable tie. It would work, but you had to give the drum a spin by hand when it hit the spin the cycle. This probelm further caused the premature wearing of the drive belt, due to slippage. I ordered both a new spring and a new belt. Upon their arrival, I removed the two screws holding the front panel and lowered it off and out of the way. The old, worn belt was very easy to remove, as there was very little tension on it. Next I attempted to remove the washer that holds the idle arm on. It is in a very awkward spot, and it appears the the washing machine is sort of built around it. I bent it gradually with locking pliers until I could force it off with the blade of a flat screwdriver. Then the idler arm was easy to lower of its axle by twisting the drum a bit and pulling it to one side. I put the new spring into the idler arm, making sure the plastic bushing was in place and replaced the arm. I then repositioned to belt and replaced the front panel. It works great now.

Removed fastening screw and Agitator. Removed and replaced Agitator Drive Block. Replaced and fastened Agitator. Done in 5 min.

Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.

Very happy camper here!

I removed front and top of washer to get acess to the tub. removed cap to tub along with inner tub and agitator. the hardest part is removing the springs on the bottom and tilt it forward to get tub out. removed belt, pulley and bolts holding transmission in place. reassemble using silicone grease on seals and washers. works great now

Had to remove tub to get to rear wall to make the repair and then put it back together in reverse order.

Pulled old knob off and pushed new one on

Unplugged machine.
Turned off water supply.

Removed front panel.
Pushed in on belt tensioner, removed old belt, replaced with new belt.

Used pry bar to lift the base assembly high enough off the snubber to remove it. Partially propped it with 2x4 wood scraps.

Used bent clothes hangar to remove old snubber ring, to protect my hands.

Replaced snubber, arrow pointing up.
Carefully lowered base assembly.

Replaced front panel.
Turned water back on, plugged back in, washing machine no longer 'walks'.

Remember to check the washer against a level if you moved the machine.

Installer unscrewed the screws on the upper panel, loosened the pulley holding the rubber drum cable, and pulled the drum up and out of the unit. With the rear heating element exposed, he unplugged the wire connections to the heating element, unscrewed the four screws holding the element to the rear panel and took the element out. Then he installed the new heating element by re-applying the four screws into the rear panel. He then replaced the thermal limiter which was directly at the right of the heating element by unplugging the wire connections to the thermal limiter and then unscrewing the thermal limiter from the rear panel. The process to install the new thermal limiter was the reverse process. He didn't install a new High Limit Thermostat because there was one attached to the new Heater. When all the new parts were installed, he reinstalled the drum by pushing the rear nub of the drum into the whole at the center of the heating plate. He then placed the rubber drum cable around the drum with the rough service facing the drum, placed the cable on the pulley and adjusted the tension of the cable with a screw driver. He then reinstalled the front panel by aligned the screw holes and reinserting and tightening the screws.

removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!

fast shipping too! will recommend others!

The first thing I did was cheked the electrical panel and breaker, then I checked the electrical cord, then I did check the motor on the bottom of the machine (that may be is the blower motor) looking for any indication of burned parts or broken, then I checked the on-off switch with a voltmeter looking for continuity and it was fine. Then I checked the timer switch and it was fine as well. Finally, I took the lid off the top of the dryer machine to check the thermostat and themal limiter fuse. The thermostat was fine but the thermal fuse was open. So after doing some research to understand how the fuse work I decided to place an order to get a new fuse. I installed it and the dryer started working again. After replacing the fuse I monitored the dryer machine while operating it and worked fine. Why the fuse was open or was damaged? It is the first time I have problems w/ the dryer. I checked the end of the conduct line that guide the air out and I noticed and have to clean the end of it because it was dirt. Because it was not completly clean, the dryer got overheated. It took me sometime to figure out the problem but I learned, save me money and the best part was that I do it myself : )

I removed the broken door latch & strike with pliers. Then I pushed the new parts into place