FLXG52RBT4 Frigidaire Washer Dryer Combo - Instructions

The appliance is gas, which made me a little nervous. However, knowing that I had the gas off, I carefully began disassembly. The burner unit is a very simple set up and within a few minutes I had the entire assembly out and noticed that in fact the igniter was broken. I ordered a new one from partselect.com and it was delivered in 2 days! The worst part of the assembly was when I accidentally bumped the new igniter against the underside of the dryer and broke the brand new one!!!..So, I ordered a second igniter and 2 days later installed it in about 30 minutes.

Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)

Smelled burning rubber, checked belt. Belt was cracked and worn out. Easy repair. Removed front of the machine held together with two screws at the bottom of the unit. Removed top cover of machine (the part with the lid). It just pops off. Pushed tensioner wheel in and took off old belt. Putting new belt on was super easy. Working like a champ now. $20 total with shipping. Not too bad to save a washing machine.

I definitely would not have tried to do this had it not been for the other testimonials written here. But it sounded so easy, I had to just try it (the repair man estimated that with parts and labor, we would be looking at somewhere between $250 and $300!).

The repair itself took less than 15 min, but I spend a good deal of time looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.

It works!!!

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Installation was easy, however watch repair instructions video for your model number to easily remove front access panel.

Placed new lint filter in proper slot.

Put machine on dolly. Tilted it on its back. Put screw driver into sheared leg and unscrewed broken leveling leg. Then screwed new leg in and tilted machine back up.

Order the Bearing Kit and Belt. All the necessary parts are included. I used them all and everything fit perfect. For the stack unit have a step stool to reach the screws on top. Remove the top screws. Remove the front panel and door assembly. Be sure to disconnect the electrical connector behind the control panel before you pull out the door assembly. Remove the belt. Pop up the dryer drum and remove. Replace all the bearing parts with new in the kit. Hang the new belt around the drum and reinstall the drum. Connect the belt using the access panel on rear of unit. Reinstall the front panel, door assembly and top panel. A helper to install the new drum bearing bracket is handy.

As instructed by a Frigidaire Video for a Laundry Center: FIRST disconnect the power I then removed the access panel, Safety Shield was missing (previous Serviceman never replaced), Entire door assembly and the top cover. Doing this exposed the entire Drum and made installation VERY easy. Always research your job as there are many reliable videos instructions available, it takes the fear and guess work out and leaves only confidence ahead. I am 63 yrs old and if I can attempt this anyone can!

1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

Pump replacement quite simple - most difficult part of job was figuring out how to disassemble outer washing machine panels. Pump required disconnecting 2 hoses and an electrical connection.

The loud noise was present only while using the dryer of my washer/dryer combo unit. I traced the noise down to the rear center of the dryer and I noticed that the noise would stop or be quieter if I pushed on this area with my hand while the dryer was running. I realized there must be some type of bearing supporting the weight of the dryer drum while allowing it to rotate. I did a Google search for parts on my model # and found Parts Select. I used the parts diagrams to figure out what parts were the likely problem. I found the rear bearing part# and watched the very helpful video showing how to replace it.

I removed the drum on my dryer and found the bearing and socket to be completely dry (no grease) and showing a lot of wear. The dryer heat element surrounds the bearing so I think 10 years of use had dried up all the grease. I purchased the bearing kit so I swapped out the old parts for everything in the kit. I also noticed the drum belt was split in places and little black dots all over the inside of the drum area were small pieces of the belt. I replaced the belt and took the opportunity to vacuum the drum area because it was covered with 10 years of lint. The bearing replacement video was extremely helpful and I was able to replace parts easily even though I had a different dryer than in the video. My dryer is much quieter now and I didn't have any screws left over!! I will definitely shop Parts Select again!!

This link provides clear simple instructions which I was able to use successfully.

Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.

Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.

Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.

I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.