MLXE42REW4 Frigidaire Washer Dryer Combo - Instructions

First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!

filter inalled

Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.

Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.

no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!

The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installation for DIY. The new legs work great.

Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)

I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out belt by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.

The loud noise was present only while using the dryer of my washer/dryer combo unit. I traced the noise down to the rear center of the dryer and I noticed that the noise would stop or be quieter if I pushed on this area with my hand while the dryer was running. I realized there must be some type of bearing supporting the weight of the dryer drum while allowing it to rotate. I did a Google search for parts on my model # and found Parts Select. I used the parts diagrams to figure out what parts were the likely problem. I found the rear bearing part# and watched the very helpful video showing how to replace it.

I removed the drum on my dryer and found the bearing and socket to be completely dry (no grease) and showing a lot of wear. The dryer heat element surrounds the bearing so I think 10 years of use had dried up all the grease. I purchased the bearing kit so I swapped out the old parts for everything in the kit. I also noticed the drum belt was split in places and little black dots all over the inside of the drum area were small pieces of the belt. I replaced the belt and took the opportunity to vacuum the drum area because it was covered with 10 years of lint. The bearing replacement video was extremely helpful and I was able to replace parts easily even though I had a different dryer than in the video. My dryer is much quieter now and I didn't have any screws left over!! I will definitely shop Parts Select again!!

This is a washer/ dryer combo unit. Start at the top of the unit. Remove top plate then remove cover between dryer and washer. Remove control panel. Now remove front panel with dryer door. Unplug harness connector. With area now open put on new belt around drum and motor. Be sure you put belt around idler pulley correct way so there is tension on belt. Put back together in reverse order. Took me about 40 minutes since I cleaned and vacuumed out appliance.

Ordered this part to replace a drain hose that had been cut short on the washer. Installation was straight-forward. Removed the two front screws to access the cabinet. Locate the drain hose and remove with a pair of pliers. Install the new part and attach the clamp with the pliers just like removal. Took about 15 minutes.

I used the percentage scale on this website to try and determine the likely cause. After reading several sites, I couldn't make sense of the timer not working on just one type cycle. When I got the dryer drum off, I could plainly see that one of the heater coils was broken. They get heat stressed and break down over time and a hard shake probably finished this off. This unit is 5 plus years old. It was Saturday and I had no heater, so I actually found it at a local parts supplier. Also replaced the drum bearing and the bearing cup in the rear along with the heater. BTW, a new heater comes with a HIGH thermal switch attached to it so don't buy it extra. The bearing cone also comes with a new bushing in the pack. I DID use the Thermal Limiter that I order from the site because I was already in there. Everything works great now. I may have gotten most off my parts elsewhere but this site was the biggest help of them all. I will definitely be back here again.

1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

As instructed by a Frigidaire Video for a Laundry Center: FIRST disconnect the power I then removed the access panel, Safety Shield was missing (previous Serviceman never replaced), Entire door assembly and the top cover. Doing this exposed the entire Drum and made installation VERY easy. Always research your job as there are many reliable videos instructions available, it takes the fear and guess work out and leaves only confidence ahead. I am 63 yrs old and if I can attempt this anyone can!

Installation was easy, however watch repair instructions video for your model number to easily remove front access panel.