FLCE7523AW1 Frigidaire Washer Dryer Combo - Instructions

Took it apart and installed the parts. Then I threw the dryer in the trash and bought a new one.

Just opened package and popped the part right in!

I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado

First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.

lacked instructions. Internet yielded a simple paragraph. Scored real bonus when we discovered the lint build up past the internal filter was approaching catastropic level. Replaced the exhaust tube (plastic) with rigid metal and resolved to disassemble and clean dryer on 2 year cycle in future. Kit just isn't complete without detailed instructions. Parts were complete and sufficient. Local codes have eliminated the plactic exhaust tube. Recommend that all old installs refit to rigid or semirigid before the fire happens!

just changed filter

I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

Popped the topped using a putty knife to free two clips in front. Remove two screws now accessible on the front inside panel. Remove two wires to door switch. Remove rear access door, two screws. Remove belt from tensioner in rear and remember or take picture of how it goes. Lift barrel slightly and pivot front panel out of the way. Lift barrel free from ball socket in rear. Lift out from front panel area. R & R kit and put back in reverse order.

just put it in the dryer filter area

I first diagnosed the problem using a Google search. Amazing how many hits I got and after reading a few was pretty certain what the cause was and what parts I probably needed to make the repair.
Some of the articles I read had links or mentioned PartSelect, so I searched for my model # and found the parts I would probably need. Knowing that I could probably get the parts I needed I disassembled the dryer (pretty easy really) and removed the old suspect part. It was devoid of lubricant and the bearing and ball showed some wear so I ordered the Bearing Assembly suggested by PartSelect (the illustrations looked just like my old parts). I left the dryer disassembled while I waited for the part, figuring it would take a week or so to arrive.
Much to my surprise, the part arrived three days later and after cleaning the dryer innards of all collected lint I put it all back together in 30 minutes.
So for a little research, a $30 part, and about an hour of my time, I have a clean and quiet operating dryer. I see no reason I can't get another 10 or so years out of it.
I consider myself a reasonably handy guy but had never worked on a dryer before. I'll be unlikely to ever call a repairman without first doing some investigation and seeing if the parts are available. With the internet and PartSelect I think I could take on a lot of other repairs I'm not familiar with. Thanks for a great outcome this time around.
Kevin

All I had to do was pop in the new door catch. Works perfectly.

removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!

After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.

I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

FOLLOW THE VIDEO!! I was scared to even get into it until I watched the video. Made it easy for me and I have little to no mechanicl skill. Excellent video that made it super easy. Took me an hour as I was taking my time. Now I could probably do the same repair in 20 minutes.