FFLG3900UW2 Frigidaire Washer Dryer Combo - Instructions

Unplugged dryer, removed access panel on the back of dryer. Removed access panel on the front of the dryer. Removed the front panel of the dryer. Inside the drum, removed the three screws on the center bearings. Slide the bearing out of the bearing support. Replaced the bearing support. Then reassembled the drum. Replaced the belt an reassembled the dryer. Two people would be recommended for reassembly.

Removed front and back panels as well as the dryer front, placed belt on drum and drive motor. I found that taking the door off the dryer front made the reassembly much easer.

I seen a post on your website referring to the exact problem I was having. One of your staff recommended changing the control thermistor, which I did following the U-Tube video link you supplied. The repair went well and the dryer now operates perfectly ! Thanks for the accurate and helpful info.

Open the top of the dryer. Removed the broken belt and replaced it with the new one I purchased from your company.

I first diagnosed the problem using a Google search. Amazing how many hits I got and after reading a few was pretty certain what the cause was and what parts I probably needed to make the repair.
Some of the articles I read had links or mentioned PartSelect, so I searched for my model # and found the parts I would probably need. Knowing that I could probably get the parts I needed I disassembled the dryer (pretty easy really) and removed the old suspect part. It was devoid of lubricant and the bearing and ball showed some wear so I ordered the Bearing Assembly suggested by PartSelect (the illustrations looked just like my old parts). I left the dryer disassembled while I waited for the part, figuring it would take a week or so to arrive.
Much to my surprise, the part arrived three days later and after cleaning the dryer innards of all collected lint I put it all back together in 30 minutes.
So for a little research, a $30 part, and about an hour of my time, I have a clean and quiet operating dryer. I see no reason I can't get another 10 or so years out of it.
I consider myself a reasonably handy guy but had never worked on a dryer before. I'll be unlikely to ever call a repairman without first doing some investigation and seeing if the parts are available. With the internet and PartSelect I think I could take on a lot of other repairs I'm not familiar with. Thanks for a great outcome this time around.
Kevin

Disconnect from electric and water supply, and move appliance to an area where you can access front, rear, and top of dryer. On rear of dryer remove the 2 screws on the small square panel, remove panel to expose dryer motor and tensioner pulley. On top of dryer remove the 4 front screws, but not the center screw, it is not necessary as it is holding something on the inside. Open dryer door and remove the lint trap, exposing the vent. Remove the 2 plastic snaps using a flat screwdriver. This will disconnect the vent from the front panel. Next remove the 2 small screws on top sides of the control panel. Remove the 2 screws on angled back panel, and remove panel. Remove approx. 10 more screws holding the under panel on, and on the bottom of control panel. Remove under panel, and slide control panel up and pull out, disconnect electrical connection on left side. Remove front off of dryer carefully, the weight of the drum is holding it in place. Vacuum everything, remove broken belt, put new belt on drum, rib side down, and slide all the way back all around. Go to rear of dryer and remove tensioner arm off of its post, there is a slot to do so, put belt on motor pulley, reapply tensioner arm in position so belt goes around it. Spin the drum a few times by pulling on the belt to make sure there are no twists. Place the front of dryer back on, put two corner screws in the top, and reseat the drum. Reconnect the electrical connection inside dryer you disconnected earlier, plug in dryer, and turn on to test. If it heats and turns well done, if not good luck. Unplug, slide vent back in, reinstall plastic clips, and ensure that vent is seated in the foam pad on the exhaust motor vent. Work backwards and put panels back in place with screws. Job done.

Popped the topped using a putty knife to free two clips in front. Remove two screws now accessible on the front inside panel. Remove two wires to door switch. Remove rear access door, two screws. Remove belt from tensioner in rear and remember or take picture of how it goes. Lift barrel slightly and pivot front panel out of the way. Lift barrel free from ball socket in rear. Lift out from front panel area. R & R kit and put back in reverse order.

just changed filter

All I had to do was pop in the new door catch. Works perfectly.

just put it in the dryer filter area

removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!

After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.

purchased part (drum belt) didn't fit the drum it was larger,, i select the size according to model number and serial number but unfortunately it was wasting of time and money and i still don't have dryer.

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!