KEWD175HWH05 KitchenAid Warming Drawer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Kansas City, MO
- Parts Used:
- WP4450934
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
After running the cleaning cycle the oven and broiler will not heat up.
After some major troubleshooting and "some" help from support folks at fixya.com I was able to pin the problem down to a blown thermistor. The repair was very simple - pull the back plate off and remove the two screws holding the thermistor in place. Replace thermistor and test both heating elements. I assume during the cleaning cycle the thermistor was over heated. Makes one wonder if it was a faulty thermistor or will it happen again on the next cleaning cycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Destrehan, LA
- Parts Used:
- WP9760767
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler Element quit working
Scarey> First thing you should do is cut off the electricity at the main breaker box. I dam near blowed myself up. It's 220Volt I found out after all hell blew up in my face. I was lucky and didn't get shocked.I shorted out the old broiler element.
So I made the job real easy I called a professional to come install the new broiler element.
I suggest you put a big red paper in each box that says turn off the power first. If your not sure how to do that call a pro.
So I made the job real easy I called a professional to come install the new broiler element.
I suggest you put a big red paper in each box that says turn off the power first. If your not sure how to do that call a pro.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Roswell, GA
- Parts Used:
- WP9760767
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broiler would not work
Went to PartSelect on the internet and looked up my model. Next I selected the problem from a short list of questions, which indicated the broil element was the problem 99% of the time. With this bit of confidence I ordered the part which was delivered in 2 days. The first step in the repair was to turn off the circuit breaker for the oven. After removing four screws that held the broil element in the oven, I pulled the electrical connectors apart on each end of the old element and attached the new unit to the electrical leads. Lastly I pushed all the wiring back inside the back wall of the oven and replaced the four mounting screws. I then performed ops check, which worked. End of story, job done in about 10 to 15 minutes. Easy Peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franz from Statesboro, GA
- Parts Used:
- WP9760767
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broil Element burned out
Turn off power at the breaker panel; remove oven door (see instructions in owners manual) and racks. Take out the 2 screws holding the element to roof of oven; next remove the 2 screws attaching the element at the rear of the oven; pull out element and disconnect wires. Attach new element to the wires and replace the 2 screws holding element to roof of oven. Next replace to 2 screws attaching element to the rear wall. Replace oven racks and door and turn power back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Point Pleasant, WV
- Parts Used:
- WP9760767
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
I am a senior adult so the screws were a little hard to reach
With some help from my wife.
Was this instruction helpful to you?
Thank you for voting!