RBD305PDB14 Whirlpool Wall Oven - Instructions

We had to remove two screws from the bottom of the outer glass door that held two brackets. Those brackets held the glass door in place. Then we had to remove two more layers of glass after that using a screwdriver. Then the inner glass, which was the one broken, we had to use pliers to bend the metal tabs that were holding it in place. We got the new glass in, bent the metal tabs back, returned the other two layers of glass, and then slide the outside glass door back in and returned the two brackets at the bottom. The hardest part was figuring out how to get started. Once we removed those bottom brackets, it was pretty easy after that.

I went online to read the instruction. Started doing it and was done in less than 30minutes. It was easy and the replacement part was inexpensive and got shipped in really fast. I probably would have spent hundreds of dollars if i called a handy man to repair it. THANK YOU VERY MUCH.

I used a cordless screwdriver to remove the retaing screws. One of the connections was pucshed back too far and was almost hidden in the hole. I used the tweezers to pull it out, replace the bake lelement and the retaining screws. I'm good to go!

Just removed two screws that held the top brackets on, and cleaned out the old broken glass. When the part came it, installed the two top brackets to the glass and then slide the glass into the two bottom brackets and screwed the top brackets in place. Whole job took about 20 minutes.

It was relatively "easy" at age 74. Needed phillips screwdriver and needle nose pliers (not nut driver). Put 2 binder clips on connection wires so they would not fall back behind oven. Figure I saved about $100-$200 for less than 30 minutes work.

Sensor replacement was removing 2 screws and gently pulling on old sensor until the clip comes out. Secured the other end of the wires so that it did not fall back inside. Then connected the new sensor clip to the oven wire, then gently returning wire into oven, and then screwing the sensor into place.
The baking element was easier than the sensor. Removed the 2 screws holding the element into the back bottom of the oven, and pulled the element forward to disconnect from clamps. Inserted new element into clamps and screwed it in. ***NOTE that there will be a smell from the new element. This smell is normal. If the smell continues after a couple minutes stop the oven and wait an hour before reattempting.

2 screws &2 push pull wires.

Thanks to those who replied to my intitial distress call...because of them I had the courage to attempt the repair.
First I flipped the main electrica breaker.
then I removed the screws from the main door. The next step was to pop out the pins holding the hinges. I couldn't do that no mater how much WD-40 and lubricant I used, or how hard I tapped center mass.....SO I took all the OTHER components out staring with the side facings. (1 screw right left and 2 for bottom.)
Next I took the screws holding the door together out -- then the two screws holding the clamps on the bottom of the door. At this point I lifted off the the front facing of the door by the handle and placed it with its glass, to the side.

I then had access to the two inside panes of glass. They are secured with a metal plate screwed into the metal of the inner door. When I removed the two screws securing the plate, two plates dropped to the floor and it was fortunate I was holding the glas securly as it two would have dropped.
Next, I cleaned each of tpieces of glass with oven cleaner and set them carefuly to the side.(they were crusted with brown) Lastly I wiggled the broken glass out of the small inner window, working from both the inside and the outside of the window. Becuase I couldn't open out the door.. this was an extrememly time consuming activity..but do-able.

Once the inner glass was in screwed one of the screws o the clamp plate so I could rest the glass while screwing in the second screw. Once screw two was in place I took out the retaining screw and replaceed in with the glass clamped between. Aftern that the tough stuff was done and I just reassmebled all the door parts.

This SHOULD have been much simplier! IF I could have removed the hinge pins as directed.

Anyway, mission acomplished. Oven works fine.
Thanks!

I removed eight screws to disassemble the oven door. I removed the old insulation and the brackets that held class panel in place. I installed the new insulation, tempered glass and reassembled the oven door.

Replacement of the thermal overload safety thermostat very straight forward after sliding unit out, killing power and removing two covers. Tested both old and new and both show continuity (= good). Installed new, restored power and tested for proper operation. Didn't happen. Replaced original and now have new as spare. Now suspect the double line break relay on electronic control board is failed and source of problem. It is common to both elements and immediate before the suspected thermostat in circuit.

With little reluctance..I decided to change the part myself..but was very satisfied...with two screws to detach the bake oven and install the new one.I was very happy to receive the replacement part within 24 hours of placing the order with Part select.

Removal of the broken glass was easy , and it looked like the new glass just slid back into place. Ordering of the glass was also easy, and it looked like it would work. But, when the glass arrived, it looked liked the new door was exactly 1/2 inch too wide and the handle was 1/2 each off too. There was no where that stated that the glass needs to go in from the bottom up. You must take off the door by lowering it all the way to the floor and lifting the hinges. (See the manual) Once it is off, remove the clips from the bottom. Then put the glass on. The handle has to be turned only one way. So, even though it looks like it could go either way, it doesn't. Turn it over to fit. It was easy once the door and the clips were removed.

No repair - just open the box and put the rack in my oven - voila - repaired!!! BUT let me tell you PartSelect sent the right part at the best price and I received it even ealier than I expected!!! I can DEFINITELY recommend these people and I do that very sparingly!!!! THANX!

I found the correct sized light bulb to fit the top portion of my double oven. It fit perfectly and just in time for Thanksgiving.
Thank you Part Select. It was easy to find the right size on your site and my order came in just a few days.

Purchased 2 piece broiler pan from this site