RB270PXYQ2 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paula from Harrison Township, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element was cracked in half
Pulled old one out, installed new one with a twist of the screw driver. Easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Lodi, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not heating up
I removed the two screws for the bake element, diconnected the two wires attached to the bake element. I then reattached the wires to the new bake element, secured it with the two screws and I was done. It took five minutes and the oven works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from GAINESVILLE, VA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element broke into pieces.
1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Black Mtn., NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element caught fire and burned into
turned power off Unscrewed 2 screws pulled old element out slightly . disconected wires . connected wires to new element tightened 2 screws turned power back on baked a pie. took longer to type this
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Charlotte, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element quit heating
un plugged oven from wall Unscrewed 2 screws pulled out old heating element and plugged in new heating element then plugged stove back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Kannapolis, NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old bake element burned out
removed old bake element (remove two screws, disconnect two wires. install new element connect wires, replace screws to hold in place. turn on oven to be sure it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Ardmore, PA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old element burned out
Removed the two sheet metal screws holding the element, Unplugged the contacts and plugged and fastened the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Lewisburg, WV
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element burnt out
Turned off the breaker to the stove. Removed the two screws holding the element in place. Pulled off the wire terminals, removed old element. Reconnected the two wires, slid new element into place, reinserted the two holding screws, turned back on breaker. 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from North Kingstown, RI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element burned out
The repair was easy. I turned off the power to the oven at he curcuit breaker. Using a phillips screwdriver, I removed the 2 screws that held on the old heating element. One screw came off easily. The other screw required a little WD-40 and alot of force, but I was able to get it off. I then removed the 2 wires from the terminals on the old element. Again, it required a little force and wiggling of the contact.
Reversing the process, I slid the contacts onto the terminals of the new heating element. Then, I screwed the backplate of the new heating element in place at the back of the oven with the 2 screws I had previously removed. I then restored power at the circuit breaker. The whole job took less then 10 minutes.
Reversing the process, I slid the contacts onto the terminals of the new heating element. Then, I screwed the backplate of the new heating element in place at the back of the oven with the 2 screws I had previously removed. I then restored power at the circuit breaker. The whole job took less then 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance from Oconomowoc, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower Oven Bake Element Didn't Work
Unscrewed two screws, pulled the element out of the socket, pushed in replacement element, screwed in the two screws--done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Sequim, WA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The element burned out
My husband undid the screws of the element. I went to Home Depot and they said I had to order in online. I could not find the part of the Home Depot website, so I googled the part and your business was easy to locate and order the part. It arrived in two days and I, the wife, was able to rescrew the element into place and, voila, the oven was functional again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Saline, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat
On Saturday night before Thanksgiving my Wife indicated the oven was not heating up. A quick continuity check of the element indicated the unit was burnt out. I got on line and found PartSelect, found the proper element and ordered it. On Wednesday the element arrived and I removed the oven racks, removed two screws and pulled out the element to access the terminals. disconnected the wires, reconnected the wires to the new element and reinstalled the screws. Entire time was less than 5 minutes.
Thanksgiving dinner was saved at a reasonable price.
Thanksgiving dinner was saved at a reasonable price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Bridgeton, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom baking element of electric oven burned through on Thanksgiving day. Fotunately the turkey was already baked. We ended up "baking" our stuffing on the outside grill!!
Unscrewed the two screws that held the old element to the back wall of the overn. Pulled out to reveal the two wires and connectors. Disconnected the two wires and removed old element being careful not to let the two wires recede back into the wall of the overn. Took the new element and connected the two wires. Then screwed the two screws through the holes in the element into the back wall. Easier than I thought it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from UPPER MARLBORO, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old bake element had burned out
It was so easy. I removed the baking racks. Then I unscrewed two Philips head screws that held the rack in place. Then I pulled the two connections apart from the wiring. Plugged the new element into the wiring. It was as simple as sliding it in and out, replaced the screws, and within minutes I was back to baking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Vashon, WA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower element would not heat
Very easy, thanks for the great support
Was this instruction helpful to you?
Thank you for voting!