Models > GBD277PDT09 > Instructions

GBD277PDT09 Whirlpool Wall Oven - Instructions

Jump to:

All Instructions for the GBD277PDT09

Customer:: Derek from Sun Lakes, AZ
Parts Used:: WPW10207397
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Lower heating elememt was not working and required replacement

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

Was this instruction helpful to you?

Customer:: anne from wellington, FL
Parts Used:: WPW10207397
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

bake element stopped working

removed two screws in rear of oven. pulled old element out replaced new one. piece of cake.I am a 70 year old female. if i can do it anyone can.thank you for your swift delivery.

Was this instruction helpful to you?

Customer:: Kenneth from Coppell, TX
Parts Used:: WPW10207397
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burnt out oven heat element

Turned off circuit breaker. Unscrewed two screws, although they required a square tipped screwdriver insert which I fortunately had phone estimates for this job were between $150 - $180. Could not have been easier.

Was this instruction helpful to you?

Customer:: Ira from Manchaca, TX
Parts Used:: WP9759243
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Oven not heating

Have a Whirlpool Accubake self cleaning wall oven that quit working after doing a cleaning. Found that the thermal overload safety thermostat might be the problem. Ordered the part which arrived in a couple of days. Installation was very easy and took about 10 minutes. First turn off power to the oven. Slide the oven out, remove the back panel, remove the old safety thermostat which has two wires coming off of it, and replace it with the new one. Put the back panel on and slid the oven back in. Turned the power to the oven back on and we had heat. Problem solved.

Was this instruction helpful to you?

Customer:: Gilbert from Bumpass, VA
Parts Used:: WPW10207397
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bake element stopped working.

Removed the old element by taking out two screws and replaced the new unit using the same screws. The delivery time on the new element was very quick-about two days. Thanks.

Was this instruction helpful to you?

Customer:: Philip from Bryan, TX
Parts Used:: WPW10207397
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bake element went out.

Ordered the part from partselect.com. I was amazed that it arrived the next day! It was the easiest repair I ever did. Took out 2 screws, unplugged the wires from the old element, plugged the wires into the new one, and replace the screws. Done.

Was this instruction helpful to you?

Customer:: Charlene from Ada, OK
Parts Used:: WP9759243
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

No heat after self clean

Killed the power to oven, removed oven from its enclosure (its heavy), removed back off oven and the part that needed to be replaced was right there. After that simply reverse the procedure. Honestly hardest part of whole job was remembering what i did with the screwdriver after my last home repair job. The oven is heavy you may need help.

Was this instruction helpful to you?

Customer:: Don from Davenport, WA
Parts Used:: WP9759243
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

control panel quit working, ovens would not operate

Contacted repair person on line and explained the problem. Person suggested testing the thermal fuse. Checked for continuity and there was none indicating the fuse was blown. Ordered new part and installed. Everything working again. Only problem was that the new part did not have the same connection as the old one on one end. Made substitution and it worked.

Was this instruction helpful to you?

Customer:: Marcus from Uppermarlboro, MD
Parts Used:: WP9760771, WPW10207397
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Baking element stopped working

Removed baking racks from oven. Then I removed two screws from the back of the oven that held the element in place. I disconnected the elements from the spade clips and connected the new element. I remounted the element with the 2 screws and placed the racks back in the oven.

Was this instruction helpful to you?

Customer:: benjamin from conway, SC
Parts Used:: WP4173175
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

burned out oven bulb

unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.

Was this instruction helpful to you?

Customer:: John from Richmond, KY
Parts Used:: WPW10207397
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Element burned out

Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!

Was this instruction helpful to you?

Customer:: Peggie from Gresham, OR
Parts Used:: WP4173175
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

not needed

screwed in the new oven light

Was this instruction helpful to you?

All Instructions for the GBD277PDT09