JUD24FCARS00 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- F George from Lakeland, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Ice Maker wasn't working
it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in the medical profession, IF I CAN do it , everyone CAN!!!!!!!!
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in the medical profession, IF I CAN do it , everyone CAN!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from NEWPORT NEWS, VA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker stopped making ice
First I unpluged the refriderator and removed the old ice maker. I then just simply installed the new ice maker. It was just that simple. The next morning I woke up with a full tray of ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Albuquerque, NM
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker stopped making ice
Replacing the ice maker is no big deal. Just take out the old one and replace it with the new one. The replacement, however, didn't work very well. Seemed like its timer was off, so it would dump ice cubes before they were completely frozen. So, we go shells of ice cubes. Not good. Called Parts Select, advised them of the problem, and they agreed to replace the part. Could not be happier with the customer service I received from this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from SKANEATELES, NY
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
old ice maker didn't work
3 screws and plugged in the new ice maker. It was slightly difficult to unplug the old ice maker and place the plug in the new ice maker. Still really easy. New ice maker works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Chesterfield, MO
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The plastic water fill tube got cracked when we moved. I called a parts company and they told me they couldn't just sell me the tube I would have to buy a whole kit for about $50 dollars. I decided to glue the tube. It worked for a while then it started leaking. So I thought I would have to buy
I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.
Thanks so much! You saved me a bundle!!
Thanks so much! You saved me a bundle!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Creighton from Piketon, OH
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
icemaker leaking water into ice bin - large ice mass
I first removed the bottom screw then loosened the top two screws about 3 turns lifted an then slide icemaker out a couple inches then used small screwdriver to unclip the wire conector and removed icemaker then pluged new icemaker in and tightened top screws replaced bottom screw lowered metal arm and was done. les than 10 min. it has taken me longer to write this reply than it did to install the icemaker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from delmar, MD
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
defective ice maker
First 1/4'' nut driver was needed.Then i proceeded
to remove the nut just below the ice maker in a
white bracket. Then i loosen the two nuts at top of
icemaker,enough to lift it off the clips. Then that
allowed me to unplug the plug in rear socket. Then
you plug in the new plug that came with icekaker
and reattach ice maker making shore the two top
clips slide into each other. Do not tighten unto you
incert bottom screw in lower bracket.Make sure
icemaker is push all the way up ,then tighen all
screws.
to remove the nut just below the ice maker in a
white bracket. Then i loosen the two nuts at top of
icemaker,enough to lift it off the clips. Then that
allowed me to unplug the plug in rear socket. Then
you plug in the new plug that came with icekaker
and reattach ice maker making shore the two top
clips slide into each other. Do not tighten unto you
incert bottom screw in lower bracket.Make sure
icemaker is push all the way up ,then tighen all
screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from West palm beach, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker quit
Looking at the instructions it looked like I had to rewire the the plug in the adapter. As it turns out, you don't .Using a screw driver, I released the braket mount and the nut driver loosened the nut holding the tray to the wall. It came right off when you lift it straight up and the wire assembly was exactly the same as the original. All I did was plug in the new ice maker, Hang the assembly on the loosen nuts and tighten again and put the screw back in the bottom bracket that held it in place. I spent longer looking at the instructions than I actually did in the whole replacement time. By morning we had a good amount of ice. EASY>>
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from superior, CO
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
water spilled over and out of ice maker. water would just keep coming.
New inlet valve. very easy. Part select was great. I first ordered a new ice maker, this did not fix the problem. Part select allowed me to return it and get the right part. The repair vidio was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Dacula, GA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice Maker died
Searched PartSelect database for replacement. Double checked pictures on website to confirm exact replacement.
After locating the screws, removed icemaker, disconnected cable connection.
Verified new part side-by=side with replacement. Made needed mod to icemaker water inlet. Popped in replacement ice maker, connected wiring harness, tightened screws. Waited for ice to arrive about an hour later.
After locating the screws, removed icemaker, disconnected cable connection.
Verified new part side-by=side with replacement. Made needed mod to icemaker water inlet. Popped in replacement ice maker, connected wiring harness, tightened screws. Waited for ice to arrive about an hour later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MERRIMACK, NH
- Parts Used:
- WP2196157
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Connection leaked as tube entered freezer
Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from COMMACK, NY
- Parts Used:
- 8201597
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
water supply line to refrigerator developed three pinholes
I watched the recommended you tube video multiple times. I made sure to have the tools and towels ready. I shut off the water supply line, and capped it, removed the backing, and inspected the back. By following the video, the rest was easy. I recommend removing any built up dust and dirt while you have the front apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathaniel from LATHROP, CA
- Parts Used:
- 8201597
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
We had a water inlet line spring a leak
First I tried repairing the but that did not work, so I looked online and found partselect.com, put in my part number and wammo! There it was, the same exact water inlet line, and reasonably in-expensive. I ordered it and it got here pretty quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- P from Whitesburg, GA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
icemaker quit
As directed in video clip, an excellent instruction video. Made for one of my quickest trouble free repairs in a long while.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from VINTON, LA
- Parts Used:
- 8201597
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
the water inlet tube was leaking
I watched the video on your site and it made it very easy, thanks
Was this instruction helpful to you?
Thank you for voting!