GDB277PDB1 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Waterloo, SC
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken inside oven door glass
We followed the instructions given by Parts Service. The only problem we had (Whirlpool left two screws out of spacer bracket and it fell out requiring further removable of inner glass to replace spacer. Process took about twenty minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from WEST END, NC
- Parts Used:
- WP4173175
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
burned out light
unscrew cover
remove old bulb
screw in new bulb
replace cover
remove old bulb
screw in new bulb
replace cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
Missing Retainer and screw
Simple - Removed oven door attached retainer with screw.Re attached door.
Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.
Your prices are great "Parts Select".
Jan
Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.
Your prices are great "Parts Select".
Jan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from CANTON, OH
- Parts Used:
- WPW10016550
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
air circulation fan assembly
Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- benjamin from conway, SC
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out oven bulb
unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggie from Gresham, OR
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not needed
screwed in the new oven light
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Moffit, ND
- Parts Used:
- WP9759243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
fuse blew for the fifth time
I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from dallas, TX
- Parts Used:
- WP9759243
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
after a self-cleaning cycle, oven would not warm (broiler didn't work either)
I did some research on blogs and identified the thermal fuse as likely culprit. Ordered part from PartSelect.com, but had to call the 800 number because the parts diagram doesn't show this fuse, just the thermostat. The fuse is located on the back of the oven, so it must be removed from the cabinet, but that wasn't a huge project. There are a bunch of sheet metal screws holding the top and back covers that must be removed. The fuse is held on by two screws and has two wire connections. Getting the stove out and disassembling is the hard part, but not really difficult if you take your time. I used a foot stool that was about the same height as the bottom of the oven and just slid the oven out on a piece of cardboard. Make sure you turn the power off before starting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy from Murchison, TX
- Parts Used:
- WP9759243
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
After using the self cleaning cycle, oven would not work
This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- monte from Spanish fork, UT
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not heat up
replace thermal safety switch on back of oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gayle from Shelby, AL
- Parts Used:
- WP9759242
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not Heating
Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Richmond, KY
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out
Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!
Was this instruction helpful to you?
Thank you for voting!