RB100PXK-0 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- pauline from newport news, VA
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would't heat
First removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...then replaced the old element with the new element..........(worked perfectly)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Paoli, OK
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element in our oven stopped heating
Unscrewed two small screws and took the old element out, and installed new element. It took less than ten minutes to repair. The new element works beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from HARRISBURG, IL
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake Element
Piece of cake. Removed door and racks, screwdriver to remove element. Reversed operation and back in service in no time. Good as new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Midland, TX
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
bae element burned out after 22 years.
Easiest repair I have ever done.
Removed two screws and pulled element out, exposing wiring. Pulled wiring connection apart with pliers. Attached wiring to new element and inserted element back in place and replaced screws. All done!!!
It worked.
Removed two screws and pulled element out, exposing wiring. Pulled wiring connection apart with pliers. Attached wiring to new element and inserted element back in place and replaced screws. All done!!!
It worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Pendleton from Cumming, GA
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
After 12 years the element died for the 2nd time We thought about getting a new oven, but ours has become sort of "retro" looking. I think it's from the '60s. We looked on line and found the part at a reasonable price and decided to give it a try.
I first went to the breaker box and shut off the power to the oven.
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Granite Falls, NC
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
My heating element had been melted through by some type of food and was severed into 2 metal peices. It could no longer be used without dangerous consequences.
I got my part in the mail and FIRSTLY, unplugged the entire stove from the wall. I unscrewed the old part from the front, took the panels off the back, and disconnected the element from the yellow and red wires.I removed the old part completely from the stove. I then put the new part in, reconnected the wires, screwed the part into the oven, then BEFORE putting the back paneling on, I tested it. The new element works like a dream. I then, put the paneling back on & was finished!
BE SURE WHEN YOU BUY TO CHECK WATTAGE OF YOUR OVEN TO YOUR ELEMENT. Voltage doesn't matter because most voltage is the same in any house you live in...
BE SURE WHEN YOU BUY TO CHECK WATTAGE OF YOUR OVEN TO YOUR ELEMENT. Voltage doesn't matter because most voltage is the same in any house you live in...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Eufaula, OK
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inoperative heating element
Opened circuit breaker, unscrewed old element, disconnected old heating element wire, attached new element wire, screwed new element into place, closed circuit breaker. tested element for heat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Cottage Grove, MN
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element burned out and cracked
Removed two screws, removed two clips, removed the element and rehooked the two clips and screwed the two clips back in. Zip Zip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrence from New Cumberland, PA
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element not heating
Replaced element.
Looks like I saved at least 500$
Geuss I'm Winning!
:)
Looks like I saved at least 500$
Geuss I'm Winning!
:)
Was this instruction helpful to you?
Thank you for voting!
Element burned out
Phillips screw driver to remove old element. Unhooked two leads. Reversed procedure to install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Quinlan, TX
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element burned up
unscrewed two screws, unpluged two wires, put screws back. turn off power!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!