RB270PXK1 Whirlpool Wall Oven - Instructions

Backed out two screws, disconnected two wires from faulty element, connected wires to new element, screwed back into place. (New element was ordered by phone and received the next day.)

Turn off the oven's breaker. Remove oven grates. Unscrew two screws holding in the bake element. Slowly pull the bake element out a few inches. Using pliers, CAREFULLY unattach the connectors from the ends of the bake element. DO NOT FORCE OR CRUSH THE CONNECTORS. Using your hands only, attach the connectors to the ends of the new bake element. Re-insert the element into the back of the oven. Re-insert the screws to attach the new element to the back of the oven. Turn the breaker back on. Turn the oven on bake to test the element. Go have a beer to congratulate yourself on saving $75 or more. Should take about 10 minutes if you're proceeding slowly & carefully. It'll take 2 minutes if you're reckless and get lucky, but it'll take 2+ hours if you're reckless and all goes wrong, causing you screw up the connectors and need to go buy some plus crimpers, etc.

Used screwdriver to unfasten the old element from the oven frame. Then unplugged the two wire plugs from the back of the old element. Reversed the process to install the new. Couldn't have been any simpler.

First I made sure it was in fact the lower bake element that was broken. I turned the oven on & noted the element did not glow red. I also used a laser thermometer to verify the element was at "room temperature" for the room it was in (the oven - about 200 degrees, given what the upper bake element was contributing.)
And close visual inspection showed that a section of te bake element had melted thru where something had recently spilled onto it.
Swapping it out was easy - turn off the electrical breaker controlling the oven, unscrew the bake element, disconnect the electrical contacts to it (which required pliers, since they had been on a Looong time, and a little care to not use the pliers too hard & thus break the wires or contacts), then reverse the process to install the new element.

It works great now.

My husband undid the screws of the element. I went to Home Depot and they said I had to order in online. I could not find the part of the Home Depot website, so I googled the part and your business was easy to locate and order the part. It arrived in two days and I, the wife, was able to rescrew the element into place and, voila, the oven was functional again.

simple replacement

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Grabbed my courage with both hands, then with my other hand I used a screwdriver. Delicately removed 2 screws holding the broken element. Once that delicate operation was done, I took out the old and place the new. Once again grabbed the screwdriver and with agility replaced 2 screws. Then, I turned on the oven and Voila, ready to bake some enchiladas.
Winner, winner, chicken dinner.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
reverse to install.
It was great to find a place that has the parts you need, and supper fast delivery service.

Thank you Ed Andrews
sound, lighting, and video systems engineer.

removed the screws that held the element in place. Pulled out the element out about three inches and disconnected the two wires, put the new one in, did the reverse and done. the best part was I orderd it on line after 3:oopm on a thursday and the part was delivered by saturday morning- wow!

I had no instructions, so I started by removing the two screws that seemed to hold the element together. I pulled the element forward and realized I had to seperate the element from the wires. It was an old unit so it took a strong tug but it did come apart. I was hoping at this point I was doing the right thing...I reconnected the new element , pushed it back in and replaced the screws. I was very impressed with myself! The new element heated up in no time. Yeah me!
Thank you "Part Select" for making it possible.

Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.

I took out 2 screws and installed new element! It took 5 mins.

followed the instructions. removed the old element and installed new one.

I had previously removed the element so I began by installing the new element. The wire connectors, did not fit as tightly as they did on the old element due to a slightly different shape on the element. Therefore, I had to take some needle-nosed pliers in order to bend the oven's wire connectors and make them fit tighter. Once that was done I struggled a bit to slip the connectors onto the new element but finally got them on.

There is also a 208V element available for this oven but after calling the web site's phone number was advised that the 208v is for an apartment-type oven and that the 240V is appropriate.

Everything works well!