RB100PXV0 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from Kingston, TN
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The broiler element went out.
Unplugged the range, took the bad element out, and inserted the new one. Plugged the range back in. It worked fine....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Luray, VA
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lower bake element burned out
Cut power off to oven in fuse panel...Removed door from oven, had to use flat edge screwdriver to slide hinge locks into place, Removed all oven grates, Removed left side and right side attachment screws from element, removed burned out element and unhooked wires from burnt element, reconnected wires to replacement element, reinstalled attachment screws, reinstalled oven grates, reinstalled door... Turned power back on to oven, turned oven on to bake, oven heated right up! Easy repair...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Indiantown, FL
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element melted through
Unscrewed the two screws holding the rear plate of the element. Pulled the element out far emough to reach the plugs on each side. Disconnected the plugs and plugged in the new element. Put the screws back in and it was ready to go. This was the second replacement in the last five years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn B from Tishomingo, MS
- Parts Used:
- WP3150371
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven knob was cracked and breaking.
I was able to locate the exact part needed to make my older oven work like new again. Thanks for the great online source for hard to find parts. All I had to do was remove the old one and replace it with th new one. It fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Fort Lauderdale, FL
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned Out Baking Element
Simple to unscrew the 2 screws holding the element to the back of the oven. Unclip the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from St Louis, MO
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven not heating on "Bake"
I observed that the lower heating element was attached to the lower rear of the oven by two stainless phillips screws. I removed the screws and gently pulled the element outward. The element came out easily with two large red wires attached (one on each side). I unplugged the wires and extracted the old element. I used this as an opportunity to clean the floor of the oven that was hard to get at with the element in place. I installed the new element by plugging in the two red wires and used the same two stainless screws to reattach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett from Huston, TX
- Parts Used:
- WP660579
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broiler Element broke
Unscrewed 4 screws holding element. Disengaged one wire, but 2nd one was separated while pulling through rear wall. Could not grasp the wire from the front. Then unscrewed 4 screws along sides of oven to pull casing away from wall cavity. Sat oven on a box while unscrewing 12 rear panel screws. Pulled wire through from back into oven. (Didn't need to do this because new element extended through the rear wall to access from back. Could have reattached wires to new element from the rear, but didn't realize this soon enough.)....two days later reinstalled new broiler element reattaching wires inside the oven and replacing 4 screws holding element in the oven. To replace the back panel I had to lay oven on its face so the holes on back of would fit with the rear panel. Put 12 screws back on. Then pushed oven back into wall cavity and put 4 screws holding oven in place. It is now working!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!