IBS550PRS02 Whirlpool Wall Oven - Instructions

first you have to remove door, so open door all the way, pull back the lever on each hinge, then close door all the way, it will be able to be pulled straight out then, but be careful, its a heavy sucker. I layed a blanket out on table and layed door on blanket, start by taking out screws around the edges of door, keep these in separate container.(don't lose any). now you need to separate the door in half, this can be a lil difficult, mine had grease build up on one end that I had to be scraped . pay special attention to how the brackets go and how the door comes apart, this info will be needed later, now that door is in half, you will need to start taking the 2 other layers of glass out, please pay attention how you take apart, it has to be replaced exactly right. take pics if needed. when you get to the broken glass, take out carefully, and place glass over opening, centered well. now you have to start replacing the other layers, the replaced broken glass is kept in place by pressure, once you get the other glass layers in do not lift up door, you will need to put in the screws under the door, one of which tightens the hinge base to the door, these are the screws that tighten the replaced glass, I found this out the hard way and had to undo the whole thing again to recenter the glass, once tight, just keep going backwards replacing the other half of door. once you do this you will either say, wow that stunk, or wow that was easier than I thought. if you don't have patience, then take the door and glass to a repair shop, because you are dealing with 3 pieces of glass costing 50.00 each. be smart.

Removed the door from the unit. Set the door face down on a work surface. Remove the screws and put them in a separate place from the rest of the screws (They are a different style of screw). Turn the door back over. Remove the two clips at the bottom on the door. The door front will slide down. Set the door front off to the side with the two clips and the screws. Remove the screws securing the brackets for the next level of glass (Mark which it the top and which is the bottom bracket. Place the glass, brackets and screws together. Remove the next glass/bracket assembly and set it aside with the screws. Lift the inside metal glass retainer and set it aside. Remove the old glass and install the new glass and reverse the order of the disassembly process.

I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.

Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!

Removed the old element by taking out two screws and replaced the new unit using the same screws. The delivery time on the new element was very quick-about two days. Thanks.

Ordered the part from partselect.com. I was amazed that it arrived the next day! It was the easiest repair I ever did. Took out 2 screws, unplugged the wires from the old element, plugged the wires into the new one, and replace the screws. Done.

Removed baking racks from oven. Then I removed two screws from the back of the oven that held the element in place. I disconnected the elements from the spade clips and connected the new element. I remounted the element with the 2 screws and placed the racks back in the oven.

Killed the power to oven, removed oven from its enclosure (its heavy), removed back off oven and the part that needed to be replaced was right there. After that simply reverse the procedure. Honestly hardest part of whole job was remembering what i did with the screwdriver after my last home repair job. The oven is heavy you may need help.

unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.

Contacted repair person on line and explained the problem. Person suggested testing the thermal fuse. Checked for continuity and there was none indicating the fuse was blown. Ordered new part and installed. Everything working again. Only problem was that the new part did not have the same connection as the old one on one end. Made substitution and it worked.

Have a Whirlpool Accubake self cleaning wall oven that quit working after doing a cleaning. Found that the thermal overload safety thermostat might be the problem. Ordered the part which arrived in a couple of days. Installation was very easy and took about 10 minutes. First turn off power to the oven. Slide the oven out, remove the back panel, remove the old safety thermostat which has two wires coming off of it, and replace it with the new one. Put the back panel on and slid the oven back in. Turned the power to the oven back on and we had heat. Problem solved.

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

replace thermal safety switch on back of oven

Had to screw off old terminal block & screw on new one

Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.