RBD245PDQ12 Whirlpool Wall Oven - Instructions

screwed in the new oven light

Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!

Turn off power at the breaker panel; remove oven door (see instructions in owners manual) and racks. Take out the 2 screws holding the element to roof of oven; next remove the 2 screws attaching the element at the rear of the oven; pull out element and disconnect wires. Attach new element to the wires and replace the 2 screws holding element to roof of oven. Next replace to 2 screws attaching element to the rear wall. Replace oven racks and door and turn power back on.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Unscrewed the old thermostat took off the conectors then replaced with new one, and screwed it back on.

I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.

First of all I would like to say how prompt the delivery of my oven glass was. I ordered it Thurs & it came on Sat ~ 2 days thats amazing! Ordering my glass was easy & the representitive that helped me was very nice & the price was great! My husband repaired it in about 20 minutes - very easy to istall the glass & very cost effective repairing it ourselves rather than having a repair man come out! Thanks Part Select I will recommend you to all out fam & friends most definetly!

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

Actually I ordered the rong part--I ordered a control panel when I should have ordered a control board but Partselect did a great job of sending what was ordered also a nice job of letting me return it for credit. they did a great job of what they do and I would recommend them to all.

Remove the door from the oven by rotating the two hinge locks. Place on soft working surface with inside door facing up. Remove screws from side , bottom and top of door. Place screws in groups as they were removed, the heads are different. Do not mix screws. Rotate door so outer Glass front is now on top. Slowly remove inner panel by sliding the outer glass panel towards bottom of door. Carefully remove inner portion of door with the two inner glass panels. Remove inner broken glass from innermost panel. replace with new glass and reverse operations to reassemble door. Make sure the white filler maaterial is back from edge of inner door glass or you will be able to see it from the front after reassembly.When all assembled, slide door back onto hinges relock hinges and you are ready to go.

With some help from my wife.

I found several posts about Whirlpool/KitchenAid ovens having this problem and most of the time this required a replacement of the thermal fuse. Other than the large number of screws to remove the oven and the sheet metal coverings, replacing the fuse was mostly about waiting to get the part. If I had a local dealer with the fuse, I probably could have been baking Deep Dark Chocolate Cheesecake that same evening. Even so, this particular repair should be left to those familiar with doing moderate-level handyman type repairs. You have to make sure the breaker is off and beware of the sharp edges on sheet metal. Fortunately, the fuse was easy to find using online documentation for my model. Part Select was very helpful when my original order did not arrive. Their customer service was great!

I followed the instructions given and it was very easy