RB1005XYW5 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Highlands, TX
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no heat in oven bake mode
I tokk two srews out, pulled element out, disconnected wires, put wires on new element, put screws back in, turned the breaker back on , now oven heats up fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joett from Lake City, FL
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element did nothing
Thanksgiving one week away oven broke. I ordered parts on line and was ready to cook our turkey. Ordering on-line saved my Thanksgiving!
We were so happy
We were so happy
Was this instruction helpful to you?
Thank you for voting!
Heard a crackling and popping noise when I turned on the oven
After figuring I'd have to buy a new oven, I figured out that it was the lower baking element. When I received the new part, I removed the two screws holding the element on. Gently pulled the element off the back oven wall and removed the wire connectors. Put the new element in place - rehooked the wire connectors and it works like new. The light bulb replacement was as simple as screwing in the new light bulb. Thanks, saved me alot of money.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Albany, LA
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element went out in oven.
Removed the 2 screws in back of the oven that hold the element in place. Pulled the wires out and removed the element. Attached the new element and inserted the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myrna from Fowler, CO
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the top of baked goods were not baking
turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Gaylord, MI
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
oven light not working
replaced light socket but did not repair problem. must have burned the motherboard.
pleased with service from your company.
pleased with service from your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Midland, TX
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
bae element burned out after 22 years.
Easiest repair I have ever done.
Removed two screws and pulled element out, exposing wiring. Pulled wiring connection apart with pliers. Attached wiring to new element and inserted element back in place and replaced screws. All done!!!
It worked.
Removed two screws and pulled element out, exposing wiring. Pulled wiring connection apart with pliers. Attached wiring to new element and inserted element back in place and replaced screws. All done!!!
It worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Paoli, OK
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element in our oven stopped heating
Unscrewed two small screws and took the old element out, and installed new element. It took less than ten minutes to repair. The new element works beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from HARRISBURG, IL
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake Element
Piece of cake. Removed door and racks, screwdriver to remove element. Reversed operation and back in service in no time. Good as new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Pendleton from Cumming, GA
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
After 12 years the element died for the 2nd time We thought about getting a new oven, but ours has become sort of "retro" looking. I think it's from the '60s. We looked on line and found the part at a reasonable price and decided to give it a try.
I first went to the breaker box and shut off the power to the oven.
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Granite Falls, NC
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
My heating element had been melted through by some type of food and was severed into 2 metal peices. It could no longer be used without dangerous consequences.
I got my part in the mail and FIRSTLY, unplugged the entire stove from the wall. I unscrewed the old part from the front, took the panels off the back, and disconnected the element from the yellow and red wires.I removed the old part completely from the stove. I then put the new part in, reconnected the wires, screwed the part into the oven, then BEFORE putting the back paneling on, I tested it. The new element works like a dream. I then, put the paneling back on & was finished!
BE SURE WHEN YOU BUY TO CHECK WATTAGE OF YOUR OVEN TO YOUR ELEMENT. Voltage doesn't matter because most voltage is the same in any house you live in...
BE SURE WHEN YOU BUY TO CHECK WATTAGE OF YOUR OVEN TO YOUR ELEMENT. Voltage doesn't matter because most voltage is the same in any house you live in...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Eufaula, OK
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inoperative heating element
Opened circuit breaker, unscrewed old element, disconnected old heating element wire, attached new element wire, screwed new element into place, closed circuit breaker. tested element for heat.
Was this instruction helpful to you?
Thank you for voting!