GBS277PRQ01 Whirlpool Wall Oven - Instructions

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

unscrew cover
remove old bulb
screw in new bulb
replace cover

I follow the directions on the Maytag site. It is a very simple job. I appreciate the Information I got from Becky when ordering the hinges.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

By reversing the way I removed the door hinges from the frame, per the reinstall instructions. I called the 800# and they emailed me a diagram, but the hinges depicted were different than mine. When my back feels better, I'll keep trying.

First, I'll say this website made it easy to find and order the part, it arrived quickly and reading others' reviews helped with installation. My Dad and I did the repair together, which really helped - my Dad is an fantastic handyman! We removed the door by lifting it up out of the hinges - a little difficult to get the right angle, but we succeeded with a little wiggling. We disassembled each later of glass/door, keeping each layer in order with screws so we could retrace our steps. I cleaned each layer thoroughly, which added to the time. Unfortunately, just as we were putting the last part on (exterior door with glass), the glass shattered as I tightened the screw! Ack! My Dad said it's because the glass was old and easy to shatter. Maybe I tightened the screw too much? So, back to the website I go to order the next part. We expect it to arrive soon. The bad news: another Christmas without an oven. The good news: my oven is now clean as new (I even removed the back fan cover to clean the fan - couldn't have done that without removing the door) and the parts added up to a fraction of the cost of a new oven.

I am not a big do-it-yourselfer, so maybe I might have found this more difficult than expected. When I first looked at the oven before ordering the part, I saw a couple of screws and it seemed like an easy task. However, I found that I had to remove to whole door first, which was actually easy. Then I started to remove the case. Then I removed several layers of a puzzle. Oven door had 3 pieces of glass and 3 metal brackets. The installation video was for a completely different oven. Although I got out the broken glass easily, I had difficulty reassembling. The oven diagram for the parts was even deceiving. I had to involve my spouse and after an hour of cursing everything, we finally managed to get the thing back together. Whoever designed this oven must have been a deranged German scientist. However, everything is back to normal and I probably saved a couple hundred bucks for a repairman.

I watched a video on line about how to do the baking element. I did not want to take the door off so it made it more difficult to get to the back where the connections are located. The broiler element has screws holding it up where the over element is resting on the bottom. The video said that you should test the conductivity but I did not have the object needed to do that. It was supposed to solve 99% of the problem to just replace it. When it was removed, I could see that it had a hole blown out on the coil. Problem solved without a repairman needed which would have cost alot more and I still would have needed this part.

Once the door was secured with hinge locking pins which I made out of cut off 16 penny nails,I removed the door , layed it on a soft padded piece of vinyl and proceeded to remove the inside top cover which was secured with phillips screws on the top and sides. I was then greeted by 2 sheets of glass before I could get to the front glass which was the one that cracked.These sheets of glass were secures with slotted metal frames which also required removing several screws and braces. I was then able to remove the cracked glass and replace it with the new glass panel. Then I had to reverse the steps to assemble the door which was fairly easy since I made a diagram of the steps when I disassembled the door (this saved me alot of aggravation since my memory isn't what it used to be. The door was fitted into the frame of the oven and once the hinges were in place I removed the pins and closed the door. It was at that point that I got a kiss from my grateful wife. End of story.

Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.

Had to screw off old terminal block & screw on new one