RBS277PVB04 Whirlpool Wall Oven - Instructions

The website and diagram of my oven helped me know exactly what was wrong and where to locate the problem. I simply removed the oven door and the trim, pulled the oven out of the wall. After removing the back panel I located the part and put in the new part. Then reversed the procedure.

Turned off breaker to oven. Removed 2 screws, used pliers to remove 2 wires from old element, replaced with new part, connected wires to new element and screwed in 2 screws. Turned on breaker, then oven and new element heated. Very easy!

Removed the door and laid it flat with the cracked glass facing up. applied duct tape to the broken glass to help hold it together. Removed the screws from the frame holding the glass. lifted the frame off,removed the broken glass and replaced it with the new piece. replaced the frame. and put the door back on the oven.

Replaced the lower heating element with a new part.

My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.

Turned off the breaker. Removed the door and side trims. Slid out the oven and removed the metal casements. Removed the front control board by unplugging each wire and carefully replaced them back into the exact same places on the new board. Be sure each plug is firmly seated. Then put everything back together and slid the oven back into the wall.

Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem

Removed and replaced boiler element

Thanks to video provided by PartSelect the repair was fast and easy. My second experience with an appliance repair with parts and video from PartSelect. I am a happy customer.

My oven (late 90's/early 2000's model) didn't have the flip-down hinge locks shown in the video. It seems Whirlpool/Kitchenaid changed the hinges even though they didn't change the model number of the oven. With my style hinges, you have to put Allen wrenches or bent nails in the holes just behind the hinge pins. Then close the door almost all the way and lift it out to separate the hinges. Spring force holds the nails in tightly until you replace the door. This video was very helpful:
https://www.youtube.com/watch?v=p7oRZdIN6m0

Also, my door had 3 different kinds of sheet metal screws. Two of them have similar heads but different threads. Keep track of which is which for when you put everything back together.

I followed the instructions per a YouTube video. My older model was slightly different in parts used in the video, but the general idea was the same. Very happy with current repair / parts. The door now opens smooth as glass, and I even got a chance to clean some internal parts inside the door.

https://youtu.be/tAypQqC5cxo?si=YoDaVMHtalPP3mhO

I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me to pull the connection apart.

All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.

Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.

1. Disconnect AC power 2. Remove back with several sheet metal screws. 3. Remove wires from Limit Thermostat. 4. Check Limit Thermostat continuity -- if open then Limit Thermostat is faulty. 5. Remove Limit Thermostat with two screws. 6. Install new thermostat

Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going

I was able to remove the old element and planned it with what little time off that I could. This would have been maybe 20-30 minute repair at the most. HOWEVER! I was extremely irritated screws were not included? When I called to ask if they were missing they said they didn’t come with the element. Cost me a very annoying trip to the hardware store. Not sure if I missed it on the site that they don’t provide screws - would have been nice to know that before I started. Still scratching my head as to why screws wouldn’t be included? My old ones were as beat up as the element I replaced. I was so irritated I was looking for a spot to leave feedback. Product is fine. Shipping was fine. Sending these products out as they do? Zero stars on that.