RBS245PRT05 Whirlpool Wall Oven - Instructions

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

Not difficult, but there are several layers of glass, metal, and insulation inside this door. Keep track of where the screws go and have room to lay out all the layers. You'll reach the cracked inner glass last.

Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.

I followed the instructions given and it was very easy

Removed the over door and set aside on the countertop. Removed the screws from the frame, pulled the oven out and set it on a small bench. Removed the burned out Thermal Overload Safety Thermostat. Replace it with the new TOST. Put the oven in place and secured the oven with the screws to the frame. Put the door on. Made sure it was set right. Turned on the oven heating element and it worked. Then Turned on the broiler heating element and it worked. And that was that. All done and working right.

Remove the door from the oven by rotating the two hinge locks. Place on soft working surface with inside door facing up. Remove screws from side , bottom and top of door. Place screws in groups as they were removed, the heads are different. Do not mix screws. Rotate door so outer Glass front is now on top. Slowly remove inner panel by sliding the outer glass panel towards bottom of door. Carefully remove inner portion of door with the two inner glass panels. Remove inner broken glass from innermost panel. replace with new glass and reverse operations to reassemble door. Make sure the white filler maaterial is back from edge of inner door glass or you will be able to see it from the front after reassembly.When all assembled, slide door back onto hinges relock hinges and you are ready to go.

re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.

replace thermal safety switch on back of oven

Removed with screw driver the gasket clamp at bottom of door opening and then pulled away the old gasket. Installed new gasket making sure that each holding pin was insert in mounting holes, trimmed away un-raveled gasket material at ends and reinstalled gasket clamp at bottom of door. Removed old oven racks and installed new racks.

Removed baking racks from oven. Then I removed two screws from the back of the oven that held the element in place. I disconnected the elements from the spade clips and connected the new element. I remounted the element with the 2 screws and placed the racks back in the oven.

unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.

removed two screws in rear of oven. pulled old element out replaced new one. piece of cake.I am a 70 year old female. if i can do it anyone can.thank you for your swift delivery.

Turned off circuit breaker. Unscrewed two screws, although they required a square tipped screwdriver insert which I fortunately had phone estimates for this job were between $150 - $180. Could not have been easier.