RBS307PVQ03 Whirlpool Wall Oven - Instructions

1) Look for the part at partselect.com, make sure you have the model and part number ready. Once you find the part, don't order yet. 2) Start your do-it-yourself repair by removing the oven door. On each side below are two arms/hinges, look closely and you will find locks on each side. Use your finger or flat screwdriver to slide towards you (this is where you start clicking your camera in evey step). Once you did it, wiggle the door a little bit, make sure they're unlocked, then pull it out carefully and hold it tight since it's little heavy. 3) At this point, you only need the phillips screwdriver. Look for all the screws, and unscrew it all, one step at a time (again make use of your digital camera). Remove the parts one at a time until you take out the broken inner glass. Measure it against the dimensions shown in the partselect.com. At this point you feel comfortable putting it back in-reverse, then you order the part. It took me 3 days for the part to arrive, but it's no big deal. 4) It's a bit difficult for me the first time, I can't figure out how to put them back (that's why I recommended the digital camera), plus I have to clean the inside and the other two glasses so it took me 1-2 hrs. I assure you if you follow my instructions, 15-30 minutes max, no sweat. 5) My wife promised me $300 for the labor (competitive price), I'm still waiting though.....Good Luck

shook bottle and painted waited a day and repeated

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?

Removed the door from the unit. Set the door face down on a work surface. Remove the screws and put them in a separate place from the rest of the screws (They are a different style of screw). Turn the door back over. Remove the two clips at the bottom on the door. The door front will slide down. Set the door front off to the side with the two clips and the screws. Remove the screws securing the brackets for the next level of glass (Mark which it the top and which is the bottom bracket. Place the glass, brackets and screws together. Remove the next glass/bracket assembly and set it aside with the screws. Lift the inside metal glass retainer and set it aside. Remove the old glass and install the new glass and reverse the order of the disassembly process.

To prevent this from happening use 7 #8 flat stainless steel washers per the 4 oven door holes that connect to the the handle as shims before securing the attachment brackets.

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

I watched a video on line about how to do the baking element. I did not want to take the door off so it made it more difficult to get to the back where the connections are located. The broiler element has screws holding it up where the over element is resting on the bottom. The video said that you should test the conductivity but I did not have the object needed to do that. It was supposed to solve 99% of the problem to just replace it. When it was removed, I could see that it had a hole blown out on the coil. Problem solved without a repairman needed which would have cost alot more and I still would have needed this part.

I used the manufacturers' manual as a guide and removed the door. This was not straightforward because the diagram was overly simplified. Once I figured it out, door removal was quite easy. I then took the door apart layer by layer (there are several), cleaning each part with oven cleaner, or detergent as I went. If not for cleaning, the repair would have taken half the amount of time. I then put the door together again and re-attached it. This was a little bit tricky but I got it to snap into place on the second attempt. Overall, this is a fairly easy repair and I do not have too much to add to existing comments. I would add the following: (1) Use work gloves to remove the broken glass. In fact, use gloves to handle all glass. (2) Take your time when re-assembling the door because the layers have to be lined up accurately for the screws to take and hold all of the layers together. In summary, I am very pleased with how this repair went. For 90 minutes of my time and $45, I was able to get the oven looking like new again.

first you have to remove door, so open door all the way, pull back the lever on each hinge, then close door all the way, it will be able to be pulled straight out then, but be careful, its a heavy sucker. I layed a blanket out on table and layed door on blanket, start by taking out screws around the edges of door, keep these in separate container.(don't lose any). now you need to separate the door in half, this can be a lil difficult, mine had grease build up on one end that I had to be scraped . pay special attention to how the brackets go and how the door comes apart, this info will be needed later, now that door is in half, you will need to start taking the 2 other layers of glass out, please pay attention how you take apart, it has to be replaced exactly right. take pics if needed. when you get to the broken glass, take out carefully, and place glass over opening, centered well. now you have to start replacing the other layers, the replaced broken glass is kept in place by pressure, once you get the other glass layers in do not lift up door, you will need to put in the screws under the door, one of which tightens the hinge base to the door, these are the screws that tighten the replaced glass, I found this out the hard way and had to undo the whole thing again to recenter the glass, once tight, just keep going backwards replacing the other half of door. once you do this you will either say, wow that stunk, or wow that was easier than I thought. if you don't have patience, then take the door and glass to a repair shop, because you are dealing with 3 pieces of glass costing 50.00 each. be smart.

I took the door off the hinge, laid it on the kitchen island and began to unscrew the outside screws. Be sure to have a bowl to place all the screws so none fall to the floor. I would recommend taking pictures with a camera phone as you dismantle each piece. The extra time was spent trying to remember how to put the 4 panes of glass back together....and if I had pictures to refer to it would have been easier. SECOND TIP- DO NOT have your husband help with any of this. I probably could have finished in less than 30 minutes if I was doing it by myself. Once he went to bed, the reassembly was much easier.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

INNER GLASS - A YouTube video on removing Whirlpool Oven Doors was very helpful. Cleaning the other two panels of glass with a Baking Soda paste worked like a dream. Re-assembly was fairly easy. The hardest part was re-aligning the outer glass cover's top holes so I could drive the screws in. LIGHT BULBS - To easy to describe.

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.