RBD275PVB00 Whirlpool Wall Oven - Instructions

Well, the instructions on the computer site were very easy to understand, however, the difficulty lay in the fact that we were 2 78 yr old people and getting to the inside the oven, lifting up the element so that we could see where it should be connected and get it connected was a task. We had to get down on our knees and then get back up. That was a chore within itself. But, the instructions were easy and clear.
Bottom line if us old people can do it, anyone can.

unscrew cover
remove old bulb
screw in new bulb
replace cover

I follow the directions on the Maytag site. It is a very simple job. I appreciate the Information I got from Becky when ordering the hinges.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

We followed the instructions given by Parts Service. The only problem we had (Whirlpool left two screws out of spacer bracket and it fell out requiring further removable of inner glass to replace spacer. Process took about twenty minutes.

Simple - Removed oven door attached retainer with screw.Re attached door.

Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.

Your prices are great "Parts Select".

Jan

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Unscrewed the old thermostat took off the conectors then replaced with new one, and screwed it back on.

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

By reversing the way I removed the door hinges from the frame, per the reinstall instructions. I called the 800# and they emailed me a diagram, but the hinges depicted were different than mine. When my back feels better, I'll keep trying.

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.