RBS245PRQ04 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- terrence from SCOTTSDALE, AZ
- Parts Used:
- WP4449247
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace inner glass
Only problem. stripped screw. Replaced at local hardware store. Directions were simple and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from MINNETRISTA, MN
- Parts Used:
- WP9759243
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Limit Thermostat had burned out due to high temp of self cleaning mode
1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from GARNER, NC
- Parts Used:
- WP9759243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
E1 and e15
Removed locking device
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leroy from SUWANEE, GA
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The video gave me the confidence to order the part
The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nadine from ALACHUA, FL
- Parts Used:
- WP9759243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
After using self cleaning feature oven wouldn't heat
I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from STONINGTON, CT
- Parts Used:
- WP9760771
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
REPLACED NONFUNCTIONAL BROIL ELEMENT
EASY. FOLLOWED THE YOUTUBE INSTRUCTIONS ON THE WEBSITE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emiliano from EASTVALE, CA
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Bake Element burn and stop heating up
I turn off the power in the breaker box and then unscrew the part and replace it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from TRENTON, NE
- Parts Used:
- WP9760771
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Didn't heat
Cordless drill removed 2 screws replaced element and 2 screws
Done. Didn't use new bracket
Done. Didn't use new bracket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ravi from Lakewood, OH
- Parts Used:
- WPW10207397
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element of the wall oven burned out and needed replacement.
You will need a screwdriver and two pieces of duct tape (very important) before you start.
Unscrew the plate that attaches and keeps the element in place to the oven wall. If the screws are rusty, replace those too at this time.
Very gently pull the element and the wires out into the oven cavity. Do not tug. Gently remove one wire from the burnt element and use a piece of tape to stick it to the oven wall. If you lose the wire or if it slips back into the hole in the wall, you are in trouble. Repeat with the other wire. Now assemble the new element in the reverse order, one connector at a time. Screw back the holding plate, and you are done. Takes less than 10 minutes to complete and your oven will be as good as new.
Unscrew the plate that attaches and keeps the element in place to the oven wall. If the screws are rusty, replace those too at this time.
Very gently pull the element and the wires out into the oven cavity. Do not tug. Gently remove one wire from the burnt element and use a piece of tape to stick it to the oven wall. If you lose the wire or if it slips back into the hole in the wall, you are in trouble. Repeat with the other wire. Now assemble the new element in the reverse order, one connector at a time. Screw back the holding plate, and you are done. Takes less than 10 minutes to complete and your oven will be as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAUREN from KENTFIELD, CA
- Parts Used:
- WP4449247
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper oven door inside glass cracked vertically, top to bottom. A currently common problem I discovered.
Product Select was the only distributor to have the oven door glass in stock. Kitchen Aid could not even get it for months.
INSTRUCTIONS:
Repaired the top over door glass quickly and easily by asking my son to do it.
INSTRUCTIONS:
Repaired the top over door glass quickly and easily by asking my son to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Scranton, KS
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
Missing Retainer and screw
Simple - Removed oven door attached retainer with screw.Re attached door.
Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.
Your prices are great "Parts Select".
Jan
Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.
Your prices are great "Parts Select".
Jan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggie from Gresham, OR
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not needed
screwed in the new oven light
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia M from Bronson, FL
- Parts Used:
- WPW10131825, WP9759243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven was not getting hot, neither on Bake or Broil.
I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Queen from Bryan, TX
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
The bake element was not heating.
Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.
Was this instruction helpful to you?
Thank you for voting!