GBD279PVQ00 Whirlpool Wall Oven - Instructions

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

By reversing the way I removed the door hinges from the frame, per the reinstall instructions. I called the 800# and they emailed me a diagram, but the hinges depicted were different than mine. When my back feels better, I'll keep trying.

turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse it took about two hours. second time it about an hour.

Removing the door was the first challenge but once the door was off it was a matter of disassembling the door to get access to the interior door. If you remove all pieces and line them up in the order that they are removed you have a good chance for success.

Once the door was secured with hinge locking pins which I made out of cut off 16 penny nails,I removed the door , layed it on a soft padded piece of vinyl and proceeded to remove the inside top cover which was secured with phillips screws on the top and sides. I was then greeted by 2 sheets of glass before I could get to the front glass which was the one that cracked.These sheets of glass were secures with slotted metal frames which also required removing several screws and braces. I was then able to remove the cracked glass and replace it with the new glass panel. Then I had to reverse the steps to assemble the door which was fairly easy since I made a diagram of the steps when I disassembled the door (this saved me alot of aggravation since my memory isn't what it used to be. The door was fitted into the frame of the oven and once the hinges were in place I removed the pins and closed the door. It was at that point that I got a kiss from my grateful wife. End of story.

Glued on the nameplate

Had to screw off old terminal block & screw on new one

First, I'll say this website made it easy to find and order the part, it arrived quickly and reading others' reviews helped with installation. My Dad and I did the repair together, which really helped - my Dad is an fantastic handyman! We removed the door by lifting it up out of the hinges - a little difficult to get the right angle, but we succeeded with a little wiggling. We disassembled each later of glass/door, keeping each layer in order with screws so we could retrace our steps. I cleaned each layer thoroughly, which added to the time. Unfortunately, just as we were putting the last part on (exterior door with glass), the glass shattered as I tightened the screw! Ack! My Dad said it's because the glass was old and easy to shatter. Maybe I tightened the screw too much? So, back to the website I go to order the next part. We expect it to arrive soon. The bad news: another Christmas without an oven. The good news: my oven is now clean as new (I even removed the back fan cover to clean the fan - couldn't have done that without removing the door) and the parts added up to a fraction of the cost of a new oven.

There are hinges on the door that need to be lifted up to take the entire oven door off the appliance. The screws are taken off of the door to get to the interior glass. The cracked oven door was simply taken off and replaced by the new one and the screws were put back and the door was placed by hooking it onto the appliance and the hinges were dropped down. Simple as that!

I turned off the power from the circuit breaker. I then removed the doors and the trim package from around the oven. I slid out the oven and had my husband help me lower it to the floor. I removed the back covering and then removed the wires connected to the old thermostat. I unscrewed the old thermostat and replaced it with the new thermostat. Did everything in reverse and it seems to be working very well. It took about 30 minutes total. Some sites suggested that a fuse needed to be adjusted/replaced. In this kitchen-aid double oven and I'm assuming whirlpools as well, the thermostat/fuse is one piece located on the back of the unit. It was very simple. The piece cost $47. Such a great investment of time and money. I had the piece in 2 days, without paying extra postage.

Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.

I am not a big do-it-yourselfer, so maybe I might have found this more difficult than expected. When I first looked at the oven before ordering the part, I saw a couple of screws and it seemed like an easy task. However, I found that I had to remove to whole door first, which was actually easy. Then I started to remove the case. Then I removed several layers of a puzzle. Oven door had 3 pieces of glass and 3 metal brackets. The installation video was for a completely different oven. Although I got out the broken glass easily, I had difficulty reassembling. The oven diagram for the parts was even deceiving. I had to involve my spouse and after an hour of cursing everything, we finally managed to get the thing back together. Whoever designed this oven must have been a deranged German scientist. However, everything is back to normal and I probably saved a couple hundred bucks for a repairman.

The only difficult part of this repair was figuring out how to get the oven door off. Most instructions advise you to flip the hinge locking clips, then lift off the door. But this oven does not have hinge locking clips. What it has is holes in the hinges, just behind the hinge pins. To get the door off, you need to open the door and insert some 3/16' pins in those holes, then close the door and lift it off. I almost got this right the first time, but I used 1/8" pins, and they didn't work, too small. It took me a long time to figure out to use bigger pins. Once the door is off, it's just a few Philips screws to work your way down to the glass. There are 4 layers of glass in this door.