GBD309PVQ02 Whirlpool Wall Oven - Instructions

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

First thing you must do is remove door from oven, to do this there are locks on the hinges, lift them up. Next put door into an upright position with door opened about two inches, lift up and pull away from oven. Lay door on flat surface with inside of door facing up. there are two screws at to of door and two screws at bottom of door remove them place to side. next there are four more screws on each corner of the inside of door, they also need to be removed. this will cause the inside and outside of door to come apart. Hold door together and flip over, be careful. remove outside of door put to side. there is a bracket at the bottom with two screws remove, and remove bracket. There is a bracket at top with one screw remove. there are two pieces of glass be careful remove the two pieces of glass to get to the broken piece. Clean broken glass be careful not to cut yourself. Remember how you removed everything to put back together, do everything in reverse. Good luck, it's not that bad.

find the owner's manual & follow the instructions for inserting two allen wrenches (assuming that you cannot find the "removal tools" that came with the oven) into the holes near the hinges on the door, carefully & slowly close the door with the wrenches inserted until the hinges disengage from the wall mounted oven. Lift the door away (is rather heavy). It is necessary to remove panels from the front one layer at a time to reach the 3rd layer of glass (the inner most glass that is the rather easy one to break). Be slow and methodical. Not a challenge once you study the owner's manual for door removal instructions.

took out door hinges, slightly close door, lift upwards, remove clips on bottom of door, remove screws from 2 inner layers of glass, insert new glass, perform revers order reassembly..cleaned all inner glass, and surrounding parts prior to reassembly

Instructions were clear and the work was easy. Take your time and think about what you are doing, and you won't have any problems replacing the glass.

Glued on the nameplate

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.

just popped the bottom trim on the oven , was an exact fit so install was very easy.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Ordered a replacement part and during installation tightened the top mounting screws too tight and shattered the replacement part. Ordered a new replacemnte part and installed without overtighting mounting screws. Repair went well. I caution others not to overtighten top mounting screws. These are same screws that attache the SS pull handle on oven door.

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy

The replacement door has a cushion on the top and the sides secured to the tempered glass. When you tighten these brackets they can cause the entire glass panel to break. To prevent this use seven #8 flat washers per hole on the top of the door before securing the brackets. These will act as spacers but you will still will be able to achieve enough pressure to hold everything in place when you tighten them. Hope this helps, it worked for me, florida bob!!