RBS305PRB00 Whirlpool Wall Oven - Instructions

I did not remove the door. After removing as much broken glass as possible, I removed the two screws at the bottom of the door, pushing a bit against the plastic oven vents so the screwdriver could fit into the screw heads. I then removed the two screws on top of the oven door. This releases the outside of the door. I then removed the two bottom screws holding the bracket that holds the piece of glass fitting into the slot at the top. I bent back the tabs with pliers, cleaned the last bit of glass out of the slots, and then put the new glass in and bent the tabs back as much as possible. It actually was pretty tight. The rest is just cleaning and putting the pieces back together. Just be careful as the four screws that go into the top and bottom of the door are actually different from the other screws. Just make sure you keep all screws separated and use them as removed. Not too bad, just time consuming.

I used the manufacturers' manual as a guide and removed the door. This was not straightforward because the diagram was overly simplified. Once I figured it out, door removal was quite easy. I then took the door apart layer by layer (there are several), cleaning each part with oven cleaner, or detergent as I went. If not for cleaning, the repair would have taken half the amount of time. I then put the door together again and re-attached it. This was a little bit tricky but I got it to snap into place on the second attempt. Overall, this is a fairly easy repair and I do not have too much to add to existing comments. I would add the following: (1) Use work gloves to remove the broken glass. In fact, use gloves to handle all glass. (2) Take your time when re-assembling the door because the layers have to be lined up accurately for the screws to take and hold all of the layers together. In summary, I am very pleased with how this repair went. For 90 minutes of my time and $45, I was able to get the oven looking like new again.

I watched a video on line about how to do the baking element. I did not want to take the door off so it made it more difficult to get to the back where the connections are located. The broiler element has screws holding it up where the over element is resting on the bottom. The video said that you should test the conductivity but I did not have the object needed to do that. It was supposed to solve 99% of the problem to just replace it. When it was removed, I could see that it had a hole blown out on the coil. Problem solved without a repairman needed which would have cost alot more and I still would have needed this part.

After a couple hours of frustration, I finally called the repair man and had it fixed properly. All the instructions I got from the the various websites didn't really address my model. Just getting the door off the over (with my type of lock) was a challenge. It is really important to have the proper tools for this job and I didn't have them. Live and learn.

I did some research on blogs and identified the thermal fuse as likely culprit. Ordered part from PartSelect.com, but had to call the 800 number because the parts diagram doesn't show this fuse, just the thermostat. The fuse is located on the back of the oven, so it must be removed from the cabinet, but that wasn't a huge project. There are a bunch of sheet metal screws holding the top and back covers that must be removed. The fuse is held on by two screws and has two wire connections. Getting the stove out and disassembling is the hard part, but not really difficult if you take your time. I used a foot stool that was about the same height as the bottom of the oven and just slid the oven out on a piece of cardboard. Make sure you turn the power off before starting.

Hardest part was getting the oven door off. Since I bought this house with oven already in place, I had no owner's manual. Tried to get it off with tips found on this site, no go. Went online and found the manual which said to insert allen wrench in holes in hinge, then lift up FROM THE BOTTOM. That is the key. Got door off, then found that replacing the inner glass is a multi step process that starts with the outside door, then multiple brackets to the next inside glass, then more braces to next glass, then finally you are at the broken (inside) glass.My advice would be to take pictures on cell phone or whatever of each level, so you know what goes where when you put it all back. I figured it out but would be faster with a picture. Anyway, got all together and the oven works fine, door looks great!.

I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?

Had to screw off old terminal block & screw on new one

took out door hinges, slightly close door, lift upwards, remove clips on bottom of door, remove screws from 2 inner layers of glass, insert new glass, perform revers order reassembly..cleaned all inner glass, and surrounding parts prior to reassembly

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

replace thermal safety switch on back of oven