GBD277PDB3 Whirlpool Wall Oven - Instructions

The repair went well & the part came in on time for thanksgiving thank you

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

I turned off the power from the circuit breaker. I then removed the doors and the trim package from around the oven. I slid out the oven and had my husband help me lower it to the floor. I removed the back covering and then removed the wires connected to the old thermostat. I unscrewed the old thermostat and replaced it with the new thermostat. Did everything in reverse and it seems to be working very well. It took about 30 minutes total. Some sites suggested that a fuse needed to be adjusted/replaced. In this kitchen-aid double oven and I'm assuming whirlpools as well, the thermostat/fuse is one piece located on the back of the unit. It was very simple. The piece cost $47. Such a great investment of time and money. I had the piece in 2 days, without paying extra postage.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

Have a Whirlpool Accubake self cleaning wall oven that quit working after doing a cleaning. Found that the thermal overload safety thermostat might be the problem. Ordered the part which arrived in a couple of days. Installation was very easy and took about 10 minutes. First turn off power to the oven. Slide the oven out, remove the back panel, remove the old safety thermostat which has two wires coming off of it, and replace it with the new one. Put the back panel on and slid the oven back in. Turned the power to the oven back on and we had heat. Problem solved.

Removed the old element by taking out two screws and replaced the new unit using the same screws. The delivery time on the new element was very quick-about two days. Thanks.

Ordered the part from partselect.com. I was amazed that it arrived the next day! It was the easiest repair I ever did. Took out 2 screws, unplugged the wires from the old element, plugged the wires into the new one, and replace the screws. Done.

Contacted repair person on line and explained the problem. Person suggested testing the thermal fuse. Checked for continuity and there was none indicating the fuse was blown. Ordered new part and installed. Everything working again. Only problem was that the new part did not have the same connection as the old one on one end. Made substitution and it worked.

Killed the power to oven, removed oven from its enclosure (its heavy), removed back off oven and the part that needed to be replaced was right there. After that simply reverse the procedure. Honestly hardest part of whole job was remembering what i did with the screwdriver after my last home repair job. The oven is heavy you may need help.

unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.