RBS307PDQ1 Whirlpool Wall Oven - Instructions

I turn off the power in the breaker box and then unscrew the part and replace it with the new one

Removed the door from oven removed screws from door and replaced the old hinges with new ones perfect match

The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.

Several professional appliance repair people told me I had to get a new oven (double, no less!) because "they don't make that hinge anymore." That would have been a $4-5K investment to replace two ovens that both work fine. I'm not generally a DIY person, but was inspired by a FB page I follow called "Handy Women." I got the model number out of my oven, googled "replacement hinge for ____," and found it on this site right away. $120 and about 1 week later I had my hinges. I found this video in the comments on this website that shows (without narration) exactly how to change the hinges.
https://www.youtube.com/watch?v=XzQuU2gZYhk
The only mistake I made that cost me some time had to do with the little pins you have to put into the hinge to remove and replace the oven door. They were missing from the old hinges, and it didn't occur to me to use the ones that were in the new hinges (hadn't unboxed when I started.) I used threaded bolts that were the right diameter and length. They slid right in, but then when I went to take them out, it was an ordeal with WD-40 and an Allen wrench. Then it still didn't occur to me to look at the new ones, so I went to the hardware store and bought two more things the right size without threads. Of course when I took the new hinges out of the boxes they already had the little pins in them. Annoying and time consuming rookie mistake, but my oven door now closes just fine, and I'm getting a ridiculous amount of satisfaction from my little repair job!

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Well, the instructions on the computer site were very easy to understand, however, the difficulty lay in the fact that we were 2 78 yr old people and getting to the inside the oven, lifting up the element so that we could see where it should be connected and get it connected was a task. We had to get down on our knees and then get back up. That was a chore within itself. But, the instructions were easy and clear.
Bottom line if us old people can do it, anyone can.

Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

I removed the Oven door, unscrew 10 screws, open up the dor case, clean all glass levels, replace inner glass, reassembled the door, reinstalled the door to the appliance.

removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven

removed door, took out 8-9 screws, slid door upward, and removed. took out broken glass, and replaced.

First I removed the door from the double oven as instructed in the owner's manual. Then I removed the screws holding the door together. I removed the layers necessary to get to the inner door glass. Then reassemled it in the order that I had taken it apart. A total of 15 screws. My tip would be pay close attention to how you disassemble.
Not only did we save the cost of a repairman but because of Part Select we got the glass for less than half the price quoted to us from Kitchen Aid for the part and delivery.
Very satisfied with our experience with Parts Select

fairly easy. took a while to reassemble. otherwise all was ok.